------------------------------- | -- COSY131/FLEXY Devices -- | ------------------------------- Version 14.8s0-- 2023/12/21 ---------------------- FIXED [FLEXY]: Update APN list (Germany & Canada) Version 14.8s0PR2 -- 2023/09/15 ---------------------- ADDED [FLEXY]: New option to send files over HTTP(S) without using chunked packets (New COM parameter: "BasicChunkedOff") ADDED [FLEXY]: Support for TLS 1.2 for VPN connections (OpenVPN Version 2.4.9/OpenSSL 1.0.2u) FIXED [FLEXY]: Flexy MQTT client may get stuck after publishing many messages without connection. FIXED [FLEXY]: Tag pages 10 & 11 no more working. FIXED [FLEXY]: Increase OPCUA IOServer Secure Connection timeout to 15 seconds (Issue occuring with S7 PLC) FIXED [FLEXY]: Miscellaneous fixes for Flexy Extension card 4G NA (FLB3208) Version 14.7s2 -- 2023/07/27 ---------------------- FIXED [FLEXY]: Revert read SMS command for FLB3203 (Verizon) (Regression of 14.7s1) [Deprecated]Version 14.7s1 -- 2023/04/19 ---------------------- FIXED [FLEXY]: Unexpected Reboot when sending lots of data through HTTPS using $dtHT (RequestHTTPX) FIXED [FLEXY]: Improvement in handling of LOG and LOGGROUPIO Version 14.7s0PR2 -- 2022/11/21 ---------------------- CHANGED [ALL] MODEM : new default values for COM parameter "DOErrRst" (6) and "DORetryInt" (300) for all modems. FIXED [FLEXY] MODEM : Issue regarding the reading of incoming SMS using FLB3208 FIXED [FLEXY] OPCUA Server: Unexpected reboot occurs in case of improper client disconnections FIXED [FLEXY] OPCUA Server: Alarm Timestamp returned by the Ewon OPCUA Server was not the time of the alarm Version 14.6s0 -- 2022/06/21 ---------------------- -- Standard FIXED [ALL]: Some special characters were not handled properly in passwords FIXED [ALL]: Importing a config.txt in a backup.tar file via USB/SD was not possible since 14.6s0PR FIXED [FLEXY]: User "Adm" was remaining in the Ewon after a backup restore not containing any user "Adm" Version 14.6s0PR -- 2022/02/04 ---------------------- -- Major ADDED [FLEXY]: Support for Flexy Extension card 4G NA (FLB3208) ADDED [FLEXY]: Support for Flexy Extension card 4G EU (FLB320A) ADDED [ALL] MODEM : Initialization phase update for Telit Modems (AT+CEMODE=2) for all 4G modems except FLB3203 FIXED [ALL] SECURITY : Vulnerability related to USB/SD commissioning -- Standard FIXED [ALL] GUI : Internet and VPN offline status correctly displayed in the GUI FIXED [ALL] GUI : Ignoring CDN choice was no longer possible ("UseCal" COM parameter) FIXED [FLEXY] GUI : Tag helper now supports I/O address format for ABLogix Tags (Ex : Local:1:xxx) FIXED [FLEXY] GUI : Alarm Acknowledgement was applied on all active alarms and not the selected ones in Alarm Summary page. FIXED [FLEXY] IOT : Better support of empty unit in MindSphere Tags FIXED [FLEXY] IOT : MindSphere unit encoding was not correct FIXED [FLEXY] IOT : Possibility of loosing small chunks of data at Mindsphere synchronisation FIXED [FLEXY] IOT : Better handling of Mindsphere Error message to detect token renewal . FIXED [FLEXY] MODEM : Add pause of 20 sec in init sequence for all Telit modems -- Continuity ADDED [ALL] MISC : Compatibility with new HW Switch component FIXED [FLEXY] MISC : Java IOServer stopped working after a period of time in specific conditions CHANGED [ALL] MISC : Maximum number of devices limit for Profinet Explorer removed CHANGED [ALL] GUI: Correction in Wireless Network Options (4G Max -> 4G Only, 3G Max -> 3G Only) CHANGED [ALL] MISC: Improvement of the internal process managing the device configuration 14.5s1 -- 2022/02/10 ---------------------- -- Major ADDED [ALL] modem: Initialization phase update for Telit Modem (CEMODE=2 at boot on Telit modem LE910NA-V2 & LE910EU-V2) ADDED [ALL]: support for a new hardware switch variant 14.5s0 -- 2021/10/22 ---------------------- Based on: v14.5s0PR 14.5s0PR -- 2021/06/22 ---------------------- -- Major ADDED [ALL] GUI: Responsive mode for smartphone ADDED [FLEXY] BASIC: String Tags support for LOGGROUPIO/LOGIO functions ADDED [FLEXY] MQTT: Last will & testament parameters added (WILLTOPIC, WILLPAYLOAD parameters added) ADDED [FLEXY] MODBUS: Advanced Option to write single values using function 06 FIXED [FLEXY] SECURITY: UpdateTagForm webform was usable by user having "ViewIO" access right only FIXED [ALL] T2M: Bidi connection issues cause extra Talk2M traffic (3 Retries every 3 sec, minute, hours). -- Standard ADDED [ALL] MISC: CA keystore updated ADDED [ALL] GUI: Help button added for each configuration page CHANGED [FLEXY] BASIC: Hide cyclic section when no script is present FIXED [ALL] GUI: Consistency of internet & VPN status icons improved FIXED [FLEXY] BASIC: improved stability (e.g. LOGGROUPIO, PRINT,...) FIXED [FLEXY] GUI: Changing Tag filters while modifying tag value was buggy FIXED [FLEXY] OPCUA :"Not enough memory" watchdog occurs when OPCUA IOServer is not connected to a server for a long time. 14.4s1 -- 2021/06/22 -------------------- FIXED [COSY APAC/JP]: Ewon fails to boot because of a modem detection issue 14.4s0 -- 2021/06/08 ---------------------- Based on: v14.4s0PR Version 14.4s0PR -- 2021/03/11 ---------------------- -- Major ADDED [FLEXY] HARDWARE: Support of 4G APAC modem extension card ADDED [FLEXY] IOSERVER: DF1 "L" register fully supported. ADDED [FLEXY] MISC: New options to allow read-only anonymous access of user webpages, EBD and viewON pages. FIXED [ALL] SECURITY: Vulnerability in the web server due to misused CORS HTTP headers (New SYS parameter "CORSAllowedHosts") FIXED [ALL] MISC: /usr folder could be erased in some reboot cases. -- Standard ADDED [ALL] MISC: Maximum connection per proxy entry Default value set to 32 simultaneous connections FIXED [ALL] MISC: NTP Event logs were displaying an incorrect "from" time value. FIXED [ALL] MISC: Anybus Bolt discovery was sometimes unstable FIXED [ALL] MISC: USBIP devices were not correctly replaced in eCatcher when unplugged/replugged FIXED [FLEXY] OPCUA SERVER: Tag Unit wrongly assigned to Alarm hint before the first value change FIXED [FLEXY] OPCUA IOSERVER: Unexpected Reboot caused by republish request (Siemens Simotion D devices) FIXED [FLEXY] TAGS: Many Tags updates caused pla-Queue full errors and possibly reboots, especially with lots of Tags Version 14.3s0 -- 2020/11/26 ----------------------------- -- Major ADDED [ALL]: Uboot update to version 2.1.2 (Can be done remotely with EDF file) ADDED [ALL]: New Profinet DCP Explorer page in configuration web interface. ADDED [FLEXY] S73&400: Implementation of String Tags writes in one block, instead of register per register. FIXED [ALL]: Enhance firewall rules between WAN, LAN and VPN interfaces for a better security -- Standard FIXED [FLEXY] IOSERVER: Ewon Flexy could reboot when writing and reading the same OPCUA string Tags at the same time FIXED [FLEXY] IOSERVER: Ewon Flexy could slow down or even reboot when writing string Tags very frequently. FIXED [FLEXY] GUI: KPI Tag description size of 64 characters removed FIXED [FLEXY] GUI: KPI Tag description couldn't be displayed properly when including quotes. FIXED [FLEXY] MISC: EBDs in TEXT and HTML format were sometimes not correctly formatted Version 14.3s0PR -- 2020/09/09 ----------------------------- -- Major ADDED [ALL]: Uboot update to version 2.1.2 (Can be done remotely with EDF file) ADDED [ALL]: New Profinet DCP Explorer page in configuration web interface. ADDED [FLEXY] S73&400: Implementation of String Tags writes in one block, instead of register per register. FIXED [ALL]: Enhance firewall rules between WAN, LAN and VPN interfaces for a better security -- Standard FIXED [FLEXY] IOSERVER: Ewon Flexy could reboot when writing and reading the same OPCUA string Tags at the same time FIXED [FLEXY] IOSERVER: Ewon Flexy could slow down or even reboot when writing string Tags very frequently. FIXED [FLEXY] GUI: KPI Tag description size of 64 characters removed FIXED [FLEXY] GUI: KPI Tag description couldn't be displayed properly when including quotes. FIXED [FLEXY] MISC: EBDs in TEXT and HTML format were sometimes not correctly formatted Version 14.2s0 -- 2020/05/06 ----------------------------- -- Major FIXED [ALL] MISC: "Out of memory" reboot/watchdog -- Standard ADDED [FLEXY] IOT: Proxy support for MindSphere connector FIXED [ALL] T2M: Fix potential watchdog in the bidi process (biditr) FIXED [FLEXY] TAGS: Automatic type couldn't be changed at tag setup update FIXED [FLEXY] TAGS: Last string Tag value was not displayed in historical table FIXED [FLEXY] GUI: "Upload on Alarm" option not visible on the Data Management config page (Talk2M API/Datamailbox) FIXED [FLEXY] OPCUA: OPCUA Connection was not recovered after a reboot when using Flexy as an OPCUA server and a WAN Static IP FIXED [FLEXY] SECURITY: SSI could be used to inject malicious script. New SYS parameter "SSIOutputMode". -- Continuity FIXED [ALL] EBD: EBD generation continued progressing in background even when the request was aborted FIXED [COSY] MODEM: 4G APAC modem was sometimes stuck and non-recoverable FIXED [FLEXY] GUI: Users login maximum length was wrongly set to 10 characters instead of 11. FIXED [FLEXY] MISC: eVCOM connection can no longer work at the second connection (New values for COM parameter "VCOMTempo") Version 14.1s1 -- 2020/04/20 ----------------------------- -- Standard FIXED [ALL] MODEM: USB IP was not working after recovery Version 14.1s0 -- 2020/02/06 ----------------------------- -- Standard FIXED [ALL] SECURITY: Improve XSS filtering on specific forms FIXED [FLEXY] GUI: Users could not log in using some complex or long username/password pairs Version 14.0s02 -- 2019/12/18 ----------------------------- -- Standard FIXED [ALL]: Bidi protocol could not recover after VPN disconnection FIXED [FLEXY]: M2Web was sometimes losing KPI access FIXED [FLEXY]: Corrected rounding of Float tags FIXED [COSY]: Modem was exported as USB device in eCatcher [Deprecated] Version 14.0s01 - 2019/11/22 ----------------------------- -- Major FIXED [FLEXY]: Historical data was erased during upgrade to Ewon firmware v14.0s0 -- Standard FIXED [ALL] GUI: Transparent forwarding window wasn't resized to fit its content FIXED [FLEXY205] MISC: USB devices were no longer listed in eCatcher [Deprecated] Version 14.0s0 - 2019/11/12 ----------------------------- Based on: v14.0s0PR In addition: -- Major FIXED [ALL] SECURITY: XSS vulnerability in the web server form "rcgi.bin" FIXED [ALL] T2M: T2M instability may cause watchdogs (biditr) FIXED [ALL] MISC: Various memory issues could cause "Out of memory" watchdogs (as of 14.0s0PR) FIXED [FLEXY] JAVA: JVM Memory leak when using IOManager readTag/writeTag methods (as of 14.0s0PR) -- Standard FIXED [ALL] T2M: Ewon Modem visible as a USB device in eCatcher after reset level 1 FIXED [ALL] INTERNET CONNECTION: "NTLM authentication" Proxy setting overwritten by the wizard FIXED [ALL] MODEM: Timeout was sometimes too short when sending SMS via cellular modem. FIXED [ALL] MISC: Transparent forwarding of Rockwell/AB devices (TCP port 44818) FIXED [ALL] MISC: Bolt configuration page unreachable (as of 14.0s0PR) FIXED [FLEXY] TAGS: Unreachable Rockwell/AB devices (DF1/ABLOGIX IOServer) reduce massively Ewon performance -- Continuity FIXED [ALL] T2M: Current operation status was truncated in Talk2M wizard result page (as of 14.0s0PR) FIXED [FLEXY] IOT: Alarms are now correctly handled by the Mindsphere data management FIXED [FLEXY] MISC: Format of /usr fails if SDEUM card present FIXED [FLEXY] MISC : Import of Tags/Users lists with some missing columns through FTP results in using the last known column value Version 14.0s0PR - 2019/09/20 ----------------------------- -- Major ADDED [ALL] GUI: Talk2M Connection Status Wizard added ADDED [FLEXY] TAGS: String tag historization ADDED [FLEXY] TAGS: String tags Rockwell support (DF1 & ABLogix) ADDED [FLEXY] TAGS: Units support ADDED [FLEXY] IOT : Siemens MindSphere data connector ADDED [FLEXY] GUI : Spanish localisation ADDED [FLEXY] JAVA: MQTT status in JAVA (ETK 1.4.4) ADDED [FLEXY] JAVA: String Tags Support (ETK 1.4.4) ADDED [FLEXY] MISC: Flash Memory Management improved ADDED [FLEXY] MISC: Transparent forwarding Target device IP address encoding added CHANGED [FLEXY] TAGS: String Tag size limited to 1KB per Tag FIXED [ALL] INTERNET CONNECTION: Ethernet gateway is lost on DHCP reconnection if interface stayed disconnected longer than the DHCP lease time FIXED [ALL] INTERNET CONNECTION: Watchdog when WAN static IP and NTP client are configured but no cable is plugged. FIXED [ALL] INTERNET CONNECTION: Possible memory overflow issue during NTP synchronization FIXED [FLEXY]: MQTT Status in BASIC wasn't updated in case of unexpected disconnections FIXED [FLEXY205]: BACNET IOServer doesn't work properly on Flexy205. NB: BacnetIP IOServer only works on Flexy LAN Port. -- Standard ADDED [FLEXY] OPCUA: Add SYSTEM option "OpcuaIOSrvIgnCertErr" for OPCUA IOServer to ignore some server certificate errors ADDED [FLEXY] OPCUA: Added KPI folder, units, and Tag quality in OPCUA server ADDED [FLEXY] EBD: String Tags Instantaneous values can now be exported in binary format (EBD) CHANGED [FLEXY] GUI: Changing memory configuration triggers automatic reboot of the device CHANGED [FLEXY] GUI: Authentication certificates upload through the GUI are now automatically trusted in OPCUA Server CHANGED [FLEXY] FILES: 2 new parameters have been inserted: "UseCustomUnit" and "Unit" in config.txt (var_lst.txt, var_lst.csv). CHANGED [FLEXY] FILES: histstr.bin, histstr.txt, inst_val_str.bin added to support string tag historisation FIXED [ALL] INTERNET CONNECTION: DNS cache issues when server IP changes frequently FIXED [ALL] INTERNET CONNECTION: PPP connection would not start on demand in some cases FIXED [ALL] INTERNET CONNECTION: DNS server cannot be configured when using Wifi Static IP configuration FIXED [ALL] INTERNET CONNECTION: LAN Gateway cannot be used when using 3G/4G Modem ext cards but no internet connection configured FIXED [FLEXY] OPCUA: "Change Configuration" user right is now needed to access usr/pki/ directory by FTP FIXED [FLEXY] OPCUA: IOServer cannot update string Tag values in batch FIXED [FLEXY] OPCUA: Writing multiple string Tags to Ewon OPCUA Server does not work FIXED [FLEXY] OPCUA: Tag Addresses containing '"' may not be polled FIXED [FLEXY] OPCUA: OPCUA Tags could be lost when added by BASIC script FIXED [FLEXY] OPCUA: IOServer shutdown after the use of the CLEAR button FIXED [FLEXY] OPCUA: IOServer Status tag has been fixed FIXED [FLEXY] OPCUA: Source and server timestamps wrongly set FIXED [FLEXY] OPCUA: OPCUA Server disconnections when one of the IP interfaces (VPN,LAN or WAN) is up/down FIXED [FLEXY] OPCUA: OPCUA Server doesn't start correctly on some WAN-ETH+WIFI configuration FIXED [FLEXY] OPCUA: IOServer was sometimes stuck when using few Tags FIXED [FLEXY] GUI: OPCUA Certificates handling improved FIXED [FLEXY] BASIC: REQUESTHTTPX with EBD does not handle DNS cache properly FIXED [FLEXY] BASIC: SETIO command using tag id or tag index didn't work properly with string values FIXED [FLEXY] BASIC: Function FS "ls" couldn't retrieve file and directory names starting with numbers FIXED [FLEXY] BASIC: WRITEEBD may fail when writing lots of data FIXED [FLEXY] TAGS: Float Tags were sometimes not properly rounded in the Tag View and in the Historical logging FIXED [ALL] MISC: Ethernet switch (Lan/Wan) could be desynchronized between the boot loader and the firmware FIXED [ALL] MISC: USBIP not working when SD Card is inserted FIXED [ALL] MISC: USB commissioning might not be processed at boot when 3G/4G modem extension card is present FIXED [ALL] MISC: Renaming inside user directory or moving files between different Media failed (ex : from /usr to /usr/sdext) FIXED [ALL] MISC: Importing config.bin via ftp crashed the device FIXED [ALL] MISC: TCP Server port conflict causes reboot FIXED [ALL] MISC: EBD process keeps running in the background even if the request is aborted FIXED [FLEXY] MISC: TagSSI for string tags truncated to 50 characters maximum FIXED [FLEXY] MISC: "Not enough memory" Watchdog when exporting Historical Table FIXED [FLEXY] MISC: Some Tags are lost when importing/updating Modbus Tag with bit selector through FTP FIXED [FLEXY205] MISC: Putting a WAN-ext card doesn't reset the Lan/Wan switch config FIXED [FLEXY205] MISC: 1:1 NAT doesn't work on WAN-ETH FLB3101 extension card -- Continuity ADDED [FLEXY] MISC: HTTP 404 error now redirects to the configured Homepage (Config page, Custom page or viewON) ADDED [FLEXY] GUI: Option to disable DataManagement export CHANGED [ALL] GUI: Remove "warning level" and "error level" column from Status pages. Remove warning/error bounds for TotalAllocated field. CHANGED [ALL] MISC: The SDConfigEnable parameter update directly (no need to reboot) FIXED [ALL] MISC: Bolt set-up stabilized FIXED [ALL] MISC: "Reboot reason: User Web Request" missing in events log after user reboot through web interface FIXED [ALL] MISC: Upgrade LED pattern was sometimes Green/Orange instead of Red/Off FIXED [FLEXY] MISC: Device format could fail in some conditions FIXED [FLEXY] MISC: High CPU usage when no cable plugged on WAN extension card and internet activated FIXED [FLEXY] MISC: SNMP tagAlUser not initialized FIXED [ALL] GUI: GUI could crash when USB devices list was empty FIXED [ALL] GUI: Scrollbar added in Diagnostic-Status submenu FIXED [ALL] GUI: Internet Browsers autocompletes specific form fields with non-related data FIXED [ALL] GUI: Some translations containing accentuated characters were badly encoded FIXED [ALL] GUI: Main page indicating "Bolt detected" even if no Bolt on the network FIXED [ALL] GUI: Improve XSS filtering on specific forms FIXED [FLEXY] GUI: Setup of PPPOutgoing with other languages than UK FIXED [FLEXY] GUI: VPN "point to point" mode now sets VPNDrvMode to TUN FIXED [FLEXY] GUI: BASIC IDE: Fullscreen mode was propagated to other pages. FIXED [FLEXY] GUI: BASIC IDE: DMSYNC, WRITEEBD and FS functions weren't set in bold when used FIXED [FLEXY] GUI: Data Management Selection set to T2M API by default version 13.3s0 - 2019/06/14 -------------------- -- Major FIXED [ALL]: Encryption of password and configuration strings with a stronger algorithm version 13.2s1 - 2019/02/28 --------------------- -- Standard FIXED [ALL]: Since January 2019, PLC discovery feature requires firmware 13.2s1 or higher. CHANGED [ALL]: ASPU improvement. [Deprecated] version 13.2s0 - 2018/12/10 ---------------------- Based on: v13.2s0PR In addition: -- Major FIXED [ALL]: Device rebooted during Internet wizard when NTP was enabled FIXED [FLEXY]: OPC UA server stopped working after the reboot of an eWON with a fixed WAN IP address -- Standard ADDED [FLEXY]: Hostname are now supported in OPC UA server FIXED [ALL]: Static routes are correctly saved in DE, IT and FR languages FIXED [FLEXY]: Historical graph now uses the local time, and no longer UTC FIXED [FLEXY]: String value with semicolon or double quote are correctly exported/imported FIXED [FLEXY]: BASIC function ONDATE now uses the local time -- Continuity ADDED [FLEXY]: Certificates upload from the GUI has been added in OPCUA Server configuration page CHANGED [ALL]: "ErrorMuteEnabled" parameter is set to 1 by default FIXED [ALL]: Some time zones were not handled correctly FIXED [ALL]: Date & time format is now based on ISO8601 specification [Deprecated] version 13.2s0PR - 2018/11/12 ---------------------- ADDED [ALL]: Etc/GMT[+/-]X time zones are added in the time zone picker ADDED [FLEXY]: Data can now be exported using UTC timestamps. New UTCExport parameter added. (default value:0) ADDED [FLEXY]: Basic's GETIO and SETIO added for string tags FIXED [ALL]: No reboot message "set new IP" was logged when set IP address with eBuddy FIXED [ALL]: PPP connection would not start on demand in some cases FIXED [ALL]: Emails are now sent with a timezoned time if UTCExport is 1 so that emails client can interpret time correctly. FIXED [ALL]: Overall NTP stabilization FIXED [ALL]: Talk2M Wizard in German language never ends when cellular connection is used FIXED [FLEXY]: Could not upload OPCUA certificate if OPCUA IOServer had never been launched [Deprecated] version 13.1s0 - 2018/10/11 ----------------- Firmware available for Cosy 131 only. Based on: v13.1s0PR [Deprecated] version 13.1s0PR - 2018/10/11 ----------------- ################# WARNING ################# # The Ewon date & time is now based on timezones where UTC is the reference. # More info in "KB-0284-00: UTC timestamp logging as of firmware 13.1s0" on ewon.biz/support ################# -- Major ADDED [ALL]: Easy APN in the Internet wizard, list possible APNs ADDED [ALL]: eWON commissioning through USB(same as SD card) (Firmware recovery required for *.(d)ebu support) ADDED [ALL]: eWON now supports Timezone/DST. Timezone selection widget added in wizard and configuration pages ADDED [ALL]: NTP server ADDED [ALL]: Wizard to easily configure Anybus AWB/Bolt devices on the eWON LAN network ADDED [FLEXY]: New KPI property in TAG settings. KPIs displayed in summary page (Maximum 6 KPIs). ADDED [FLEXY]: Support of Strings TAGs(OPCUA server, I/O Server: MEM/S7/OPCUA, viewON) CHANGED [Flexy]: Due to string tag and KPI support, the var_lst.txt, var_lst.csv and config.txt tag structure has changed. The place of the "tag type" column was moved. A new column has been added for the KPI. CHANGED [FLEXY]: Data logging in UTC FIXED [ALL]: Cosy 131 4G NA and FLB 3205 extension card causes reboot with some SIM Cards FIXED [FLEXY]: Retentive tags caused bootloop on update from 13.0s0 -- Standard ADDED [FLEXY]: Certificates supports in OPCUA Client/Server (signing, encryption and authentication) ADDED [FLEXY]: Data Management: Live Data and KPI publishing options ADDED [FLEXY]: New BASIC/webform function "FS" to manipulate filesystem (mv, cp, ls, etc.) CHANGED [FLEXY]: Data Management: configuration page layout modified FIXED: 4G Modems [ALL]: SMS stops working with error "eserial-write-failed (Input/Output error)" FIXED: Miscellaneous [FLEXY]: Outgoing connections with no WAN cards was not working FIXED: OPCUA [FLEXY 10X]: OPCUA client and server enabled FIXED: OPCUA Server [FLEXY]: all network interfaces exposed as endpoints during Discovery -- Continuity ADDED [ALL]: Ability to configure custom DNS entries in eWON DNS relay ADDED [ALL]: New EBD parameter [$ts] to export in UTC or Local time. ADDED [ALL]: Build number displayed in the GUI footer ADDED [FLEXY]: BACNET IOSERVER: Pulse_Converter object added ADDED [FLEXY]: MODBUS IOServer supports baudrate of 115200 bds ADDED [FLEXY]: TSAP syntax added in S7 TAG helper ADDED [FLEXY]: VCOM, new COM parameter "VCOMTempo" to enable/disable the TCP fragmentation (disabled by default) CHANGED [ALL]: Proxy setup removed from Internet wizard CHANGED [FLEXY]: OPCUA Server: no group selection means publishing all tags FIXED: Historical Logging [FLEXY]: Reboot when using historical logging with more than 300 TAGs/sec FIXED: Internet Wizard [ALL]: fails if previously used WIFI SSID no longer available. FIXED: Internet Wizard [ALL]: WiFi with static IP and a gateway was not working FIXED: Internet Wizard [FLEXY]: APN username and password not considered FIXED: IOServer Setup [FLEXY]: Modbus TagHelper typo for 'F' and 'H' modifiers FIXED: IOServer Setup [FLEXY]: ModbusTCP reply time-out configurable even without serial port detected. FIXED: Miscellaneous [ALL]: Mounting speed improvement for EUM card (ext3) FIXED: Miscellaneous [ALL]: USB devices with 2 HUBs in series caused reboots FIXED: Miscellaneous [ALL]: WAN on demand activated for DNS queries FIXED: Miscellaneous [FLEXY]: Alarm config page not updated correctly when modified by config file. FIXED: Miscellaneous [FLEXY]: Alarms history/summary sorting by date was wrong FIXED: Miscellaneous [FLEXY]: BASIC IDE double click was crashing the GUI FIXED: Miscellaneous [FLEXY]: Dyndns could generate reboots FIXED: Miscellaneous [FLEXY]: Erasing config.txt generates reboot if OPCUA IOServer enabled FIXED: Miscellaneous [FLEXY]: Historical Table doesn't include last updated value FIXED: Miscellaneous [FLEXY]: HTTPS post queries could sometimes fail FIXED: Miscellaneous [FLEXY]: Memory leak in the data management causing reboot FIXED: TAGS Setup [FLEXY]: DWORD tag values greater than 0x8000000 are not handled correctly on Tags Values page FIXED: TAGS Setup [FLEXY]: OPCUA tag type conversion handled correctly FIXED: Users Setup [ALL]: Non-Adm user couldn't read/write files through FTP/eBuddy FIXED [ALL]: GUI was sometimes unavailable in case of internet connectivity issue FIXED [FLEXY]: Java doesn't read&write on /usr/sdext (SDCard) FIXED [FLEXY]: OPCUA IO server offline after an initialization failure FIXED [FLEXY]: OPCUA IO server support subscribing to numerous tags version 13.0s0 - 2018/04/30 ------------------- Also included: v12.3s1PR and v12.3s0PR FIXED: DI Wizard [COSY 131]: missing translations of DI wizard FIXED: Summary Page [COSY 131]: cannot reset GSM data consumption counters on the new GUI FIXED: VPN Wizard and VPN config page [FLEXY]: eFive certificates on multiline not stored using paragraph in comcfg FIXED: miscellaneous [ALL]: LED color during commissioning by SD card was green and not orange version 12.3s1PR - 2018/04/11 -------------- PRE-RELEASE VERSION NEW & fixed features: FIXED [COSY 131]: 4G JP stability with IIJ SIM FIXED [ALL]: Translations (DE - FR - IT - ES) version 12.3s0PR - 2018/03/21 -------------- PRE-RELEASE VERSION NEW & fixed features: ADDED [FLEXY]: New IO Server OPCUA ADDED [COSY 131]: Add a wizard to Cosy131 to set DI1 and DI2 behaviours ADDED [COSY 131]: Possibility to send SMS or e-mail on DI1 and/or DI2 status change. ADDED [COSY 131]: support for modem 4G EU NA APAC ADDED [ALL]: WAN Fallback on secondary interface in Internet wizard ADDED [ALL]: Support for touchscreen computers FIXED: Miscellaneous [FLEXY]: Historical Table EBD didn't output data properly in HTML FIXED: Miscellaneous [FLEXY]: EBD HT send by mail in scheduled action was not working FIXED: Miscellaneous [FLEXY]: DNS checkbox not usable on LAN eth config page (GUI) FIXED: Miscellaneous [FLEXY]: Disable WAN through Internet Wizard doesn't close the current connection FIXED: Miscellaneous [FLEXY]: Issue when using multi lines in system parameters [EMAIL/SMS content] FIXED: Miscellaneous [FLEXY]: Display issue on the VPN Outgoing/Incoming page FIXED: Miscellaneous [FLEXY]: "UpdateGraphForm" Webform not working FIXED: Miscellaneous [FLEXY 205]: Board index not working correctly with extended syntax (ex: DI3,E1) FIXED: Miscellaneous [ALL]: Reboot to recover the modem if modem is no longer detected (Error 27201/22200) FIXED: Internet Wizard [ALL]: Login/password for modem connection never used since firmware 12.2 FIXED: Internet Wizard [ALL]: Set WANPermCnx to 1 by default for WIFI FIXED: Talk2M Wizard [ALL]: UDP test too long when fails FIXED: TAGS Setup [FLEXY]: "New TAG discovered" message appears too often FIXED: TAGS Setup [FLEXY]: Realtime graph display not working anymore if time span changes FIXED: TAGS Setup [FLEXY]: Autorefresh was still applied when Setup Mode was selected FIXED: TAGS Setup [FLEXY]: Default sorting mode on Tags List wasn't convenient FIXED: TAGS Setup [FLEXY]: ALM,ACK,RTN,END checkboxes not handled correctly in Alarm notification page FIXED: Users Setup [FLEXY]: FTP directory access list not updated FIXED: Users Setup [FLEXY]: Directory restriction not working for FTP access FIXED: Users Setup [FLEXY]: Tag page security not working properly FIXED: Users Setup [FLEXY]: FTP access to /usr directory fails for user with FTP rights FIXED: J2SE [FLEXY]: Loss of precision when using array of int variables FIXED: J2SE [FLEXY]: JAVA IOServer is removed from IOServer list when jvm is stopped FIXED: J2SE [FLEXY]: JAVA, big integer values truncated by float conversion with readTag and writeTag version 12.2s1 - 2018/01/05 - Flexy 205 version 12.2s1PR - 2017/12/15 - Flexy 10x/20x & Cosy 131 -------------- ADDED: Support of Flexy 205 ADDED: New GUI for Flexy/Cosy 131 devices FIXED: OPC UA server authorization by user/password CHANGED: Displayed names for Cosy 131 CHANGED: WPA Supplicant upgraded, security improved ADDED: NTP settings displayed in wizards and default NTP server is now ntp.talk2m.com FIXED: OPC UA: ewontags folder notifies client when a change occurs CHANGED: ErrorMuteEnabled sys config default value changed from 1 to 0 FIXED: Wizard internet could be really slow when using ez IP ADDED: Support of TLS1.2 for encryption (HTTPS, etc.) ADDED: OPC UA: Tag description is now also exported ADDED: WiFiAutoscan (comcfg, default:1) Set to 0 to disable the scanning of WiFi hotspots when already associated (connected). ADDED: T2M connection check (switch UDP/TCP) ADDED: Support of J2SE 1.4.1 in eWON FIXED: T2mAccSrvAddr (comcfg parameter) is now assigned to "talk2m_pro" ADDED: OPC UA: allows the publishing by TAG or ID FIXED: OPC UA: possibility to write multiple tags FIXED: VPN Server redundancy not working correctly when using VPN Server URLs and UDP FIXED: Reboots could occur when exporting historical logging with a lot of tags CHANGED: Add eWON file access (EBD) right to all users. FIXED: BASIC IDE: file import shows a confusing path FIXED: VCOM was not working for protocols with large chunks of data coming from serial device. ADDED: BACnet server counters ADDED: Support for MQTT scripting. FIXED: JAVA: Modem connection LED control didn't work properly FIXED: Saving invalid configuration in Real Time Logging could erase the targeted tag FIXED: Data Management couldn't be triggered on alarm FIXED: PLC5 device address cannot be used directly in TagAddress definition ADDED: BASIC: LogGroupIO group$[,round%[,method%]] function to trigger the recording of tags from "group$" with the same timestamp FIXED: S5-AS511 TagHelper bad addressing version 12.1s2 - 2017/09/01 -------------- FIXED: Historical logging export (since v12.1s1PR). When a historical logging was exported with hundreds of tags, the eWON device no longer reboots. FIXED: OPCUA server. Writing multiple tags when using the OPCUA protocol in the Flexy is now possible. ADDED: EUM card. Flexy can operate a repair or format in case of respectively damaged or corrupted filesystem. FIXED: Internet Wizard (since v12.0s0). When using the EZ DHCP feature from eBuddy, the Internet Wizard could get stuck. This is no longer the case. [Deprecated] version 12.1s1PR - 2017/06/26 -------------- ADDED: Support for 4G Flexy extension card [Deprecated] version 12.1s0 -------------- ADDED: NtpUpdateOnWANCnx (config param, default: TRUE) allows to force NTP update at each WAN cnx if NtpEnabled is TRUE ADDED: BACNET IO server now supports Accumulator objects FIXED: OPCUA IO server is now compliant with "Force Read Only" tag option FIXED: bad italian translation in tag creation ADDED: improved log and diagnostic of switch monitoring FIXED: some internal events (NTP updates, etc.) bypassed the Key switch on cosy 131 FIXED: rounding to nearest integer when converting from float to integer types (IO server scaling) ADDED: Support for 4G Verizon Flexy extension card ADDED: Support for 4G NA Flexy extension card ADDED: Support for 4G EU Flexy extension card FIXED: OPCUA IO server tags in "force read only" are now updated at the client side. ADDED: DHCP client retries timeout is now configurable using com config parameter DHCPRTO FIXED: BACNET IO server caused reboots in some cases FIXED: User right ViewIO is not enough to display tag pages allowed FIXED: BASIC opening file in unexisting subdir creates a file with the subdir name FIXED: Hitachi IO server TCP polling unstable FIXED: Hitachi IO server 32 bits registers impossible to write FIXED: Hitachi IO server signed registers were displayed as unsigned version 12.0s1 -------------- ADDED: PLC discovery available on Cosy 131 and Flexy (activable using com config BroadcastForwarder) FIXED: improved speed of shutdown and reboot FIXED: Cosy 131 wizard system slow (even timeouts) when no WAN cable not plugged. FIXED: WiFi connection stability improvement FIXED: problems with GSM initialization and SMS sending FIXED: Error can be recovered in some cases by setting SWITCH_MONITOR parameter to 1. A trace "switch glitch" will be added to event log for each attempt to correct detected lock. FIXED: reboot issue when the communication with some PLC could not be established. version 12.0s0 -------------- FIXED: Flexy modbus polling is now much faster when polling a big amount of tags FIXED: Configuration parameter DHCPTO (default: 45000) now sets all the DHCP client requests timeout (expressed in milliseconds, require a reboot, 3 retries on timeout error) ADDED: PLC discovery FIXED: Proxy rule to connect SNMP device now works ADDED: BacnetIP IOserver ADDED: eWON as gateway now forwards DNS requests from LAN to WAN ADDED: WAN on demand available on all WAN interfaces ADDED: New BASIC2 function WriteEBD to stream EBD (Export Block Descriptor) content to files ADDED: User partition space extension with the SD card (EXT3) FIXED: One char was missing when using the AlarmHint Keyword in alarm email template FIXED: HTTPREQUESTX support PORT in url (example: http://www.ewon.biz:89/url) FIXED: OPCUA correctly handles "Force Read Only" tag attribute. FIXED: GSM IMSI parameter now logs as a warning, not an error FIXED: Create/modify tags while many MELSEC tags are polled FIXED: Execution of two Basic scripts in parallel is not a problem anymore FIXED: MELSEC IOServer: It was not possible to set value D (0xD) for the Y (Output) option ADDED: Bit selection for MODBUS IOSERVER FIXED: Avoid disconnecting Internet connection when sending GSM SMS FIXED: End of frame received was missing in Modbus with a slow baudrate (< 9600 bauds) version 11.3s0 - 2019/06/27 -------------------- -- Major FIXED [CD and Cosy 141]: Encryption of password and configuration strings now uses a stronger algorithm UPDATED [CD and Cosy 141]: ASPU improvement version 11.2s2 -------------- FIXED: eWON stopped polling MPI after few hours FIXED: Synchronization error with default NTP server clock does no more lead to configure an invalid date FIXED: FLEXY: Flexy equipped with WAN ethernet extension board sometimes lost its Internet connection FIXED: Security update [Deprecated] version 11.2s1 -------------- FIXED: Java ReadInterfaceInfo was returning LAN interface info when using a WAN modem connection FIXED: BASIC2: HTTPREQUESTX with empty headers issued requests with ":" headers content FIXED: BASIC2: HTTPREQUESTX wasn't working properly when the QUERY part was empty ADDED: FLEXY: Support of USB 3-ports extension board ADDED: FLEXY: Support of IO 4-20mA extension board FIXED: BASIC2: Recursive function calls work as expected with one character long integer parameter names FIXED: DHCP client didn't renew the lease ADDED: OPC UA server ADDED: DHCP server on LAN FIXED: Gateway route was not added for WIFI with static IP address FIXED: Default SMS subject on alarm was wrong FIXED: ParamSSI tags in web pages can be used when 'user pages security' is disabled FIXED: DHCP discovery timeout is now 7 seconds FIXED: BASIC2: REQUESTHTTPX COMMAND didn't work with HTTPs and PROXY enabled FIXED: IMSI is not read for 4G Japanese modem (subscriber id not available in Japan) FIXED: Bigger buffer for PUTHTTP (4000 bytes) ADDED: USR LED blinks red during ewon firmware upgrade on Flexy and Cosy 131. FIXED: IOSERVER: JAVA IO Server config was not set at startup [Deprecated] version 11.1s0 -------------- FIXED: reading non existing info block in Java on a Flexy used to crash FIXED: deleting a directory with Java now works on Flexy ADDED: you can add custom certificates by FTP for your HTTPS requests CHANGED: Flexy/Cosy: CA root certificates updated with last certificates from Mozilla fundation ADDED: new BASIC2 commands RequestHTTPX and ResponseHTTPX to allow REST API calls. FIXED: LAN Static IP on same network than WAN DHCP is no more accepted by eWON ADDED: Error mute: mute repetitive patterns in the event log. ADDED: you are now allowed to do HTTPS requests in BASIC2 and Java (using existing GET/PUT HTTP commands, specifying https:// in the URL) FIXED: Flexy did not reconfigure VPN when eFive public IP was changing FIXED: eWON devices were unable to reconnect to a new Talk2M server when using VPN/TCP mode. FIXED: Wifi level was not displayed on LED and on status page FIXED: IT language was proposed on Cosy 141 FIXED: Parker HMI now supported by USBIP feature FIXED: FLEXY: changed IO name limitation in tag helper from 9 to 34 to account for optional IO boards. version 11.0s0 ------------- FIXED: missing texts on some modem related messages on eWON CD's. FIXED: USBIP devices list only available for uk language FIXED: VCOM: Burst of serial data from device to eWON could lead to watchdog if serial data entered at constant rate until buffer was full. Resulted in watchdog. FIXED: BASIC2 string starting with character '@' was triggered as a function call instead of just a string. ADDED: New parameter SDConfigEnable in Comcfg to enable/disable configuration by SD card (default: ON) ADDED: It is now possible to perform a recovery with the SD card FIXED: NAT 1:1 from WAN to LAN was filtered when Talk2M wizard was executed due to a too restrictive filter. Now correctly allow NAT 1:1 packets when NAT 1:1 is enabled with T2M. ADDED: comcfg parameter T2MKey and T2MNote to allow ARK T2M registration feature (include T2M.txt on an SDCard) ADDED: SD Card can now be inserted in Flexy, Cosy 2 to configure/restore (SD Config) ADDED: new parameter in comcfg GeolocEnable (TRUE by default) to activate geoloc when connecting eWON to Talk2M. CHANGED: eWON Flexy, Cosy 2 wan eth activated with dhcp by default. FIXED: FINS IO Server, when a read request generates a Sub Response Error, the request fails, even if the main response is valid. This leads to rejecting good responses from the PLC incorrectly when the PLC encounters problems with other actors on the bus. FIXED: Email templates: when using email templates, the number of chars between 2 template's tags was limited to 100 characters (including the data itself). FIXED: BASIC 2 IOServer extended syntax caused eWON reboot. FIXED: improved usbip support for PLC Allen Bradley CompactLogic FIXED: improved usbip support for PLC Omron FIXED: WiFi BSSID roaming and connection stability improved (no more disconnection). FIXED: SMS notification with ewon CD with some simcom modems with some career was not possible during internet connection. version 10.1s0 ------------- FIXED: When gateway ports were set to 0 they were listening on a random port instead of being closed (applies to Modbus, FINS, IsoTCP). FIXED: eWON was not able to establish a WIFI connection when a full charge basic script was running. ADDED: NAT 1:1 from WAN to LAN was filtered when Talk2M wizard was executed. The Talk2M wizard WAN security has been updated to allow NAT 1:1 packets when NAT 1:1 is enabled. FIXED: USBIP: When the USBIP config is the default one, checking "Erase config" in the wizard stop and don't restart the USBIP. FIXED: An error "could not rename file to backup" was always raised after first reboot following a format. FIXED: some non standard commands in FTP/HTTP servers caused ewon reboot, security reinforcement. FIXED: Setting a breakpoint inside a function could hang the BASIC exec. queue FIXED: ViewON access rights are always set to "active" for "adm" user. ADDED: BASIC IDE: It's now possible to select and copy editor's content when program.bas is running FIXED: eWON equipped with a Simcom modem (HSUPA) could not send a SMS. FIXED: Upgrade firmware produced a "usbip-eveusbd daemon error" CHANGED: BASIC function parameters of type INTEGER can now have a name which is only 1 character long. FIXED: PROXY: It was in some cases impossible to reconnect to a VNC-enabled device after a VPN deconnection FIXED: USBIP is compatible with Omron PLC devices since the update of the Eltima driver 3.6.0 from 2015/10/1 FIXED: When Modbus PreDelayVal had a big value (ex 1000), writing modbus registers could be abnormally slow. FIXED: When too many tags were defined (ex: Modbus), it was sometime impossible to update or delete tag and eWON rebooted due to watchdog. FIXED: put file dewonfwr.edf on ewon ftp server now trigger a full reset of the eWON (sys, com, /usr, ...) ADDED: It's now possible to set the WiFi Security manually using the Wizard GUI ADDED: Different DNS and Gateway can be provided for Ethernet and WiFi WAN interfaces version 10.0s2 -------------- ADDED: specific handling of firmware upgrade to fix incorrect firmware revision in 10.0s0 and 10.0s1. version 10.0s1 ------------- FIXED: eWON equipped with a Simcom modem (HSUPA) could not send a SMS. FIXED: PPP accumulated outgoing/incoming traffic could be negative. version 10.0s0 ------------- ADDED: BASIC IDE: It's now possible to set breakpoints (add, remove) or pause the program execution for debug purpose (pause, abort, continue, step, step over) FIXED: BASIC IDE: Using Tab Key inside the editor deleted content rather than changing indentation when there was an active selection FIXED: BASIC IDE: Printing the 0 character used to block the console ADDED: NAT 1-1 allows you to remaps IP's from LAN to another IP on another network interface. FIXED: Incoming call not working properly on eWON with PSTN modem FIXED: Flexy: eWON does not reboot automatically when the GSM Modem software reset failed FIXED: USBIP devices list is well cleared when USB is powered off. ADDED: wizard, status and informations of usbip in cosy 2 web interface (wizard). ADDED: eWON unregisters all USB connected devices before disabling USB FIXED: BASIC2, labels can now be indented, adapted syntax highlighting in BASIC IDE. FIXED: BASIC2: using reference to array (function) always point to first element. FIXED: BASIC2: Invalid parameter type check when passing parameter by reference to function. FIXED: BASIC2: syntax highlight when multiple arrays on the same line is now correctly handled in BASIC IDE. FIXED: Flexy: since revision 9 the modem type text was displayed as empty, only the corresponding number was displayed. ADDED: If max number of available NAT entries drops to 0, the eWON will reboot with a specific critical error. version 9.0s0 ------------- CHANGED: WifiDeb (com config param) renamed in WIFI_DEBUG (standardization purpose). FIXED: BASIC IDE: Renaming a section in the Outline panel with the same name showed hidden section comments in the code editor FIXED: BASIC IDE: Copy-Paste in the editor used to remove leading and anchor carriage return" FIXED: Basic program saved using the basic IDE is now runnable immediately (no reboot needed). FIXED: float tags for IO Server DF1 with negative values are now correctly displayed. FIXED: eWON sends an erroneous request to eSync server when ID length is more than 20 characters and password is set FIXED: configuration menu of LAN ethernet now only show ip/mask when WAN ethernet is available (and gateway is no more diplayed). FIXED: LANWANConfig (cosy 2 switch configuration) parameter is now ignored when not on a cosy 2. FIXED: Restore backup on cosy 131 causing crash and no restore. FIXED: Unable to switch UDP connection on a secondary eFive VPN server when the primary eFive becomes unreachable. FIXED-CHANGED: Operators precedence in Basic fixed: Higher: - (unary) ^ (before ^ was at the same level as * / MOD) * / MOD + -" version 8.2.s1 ------------- FIXED: on slow connections user could experience long delay for loading WEB pages from the eWON. FIXED: FLEXY: tls-auth (openvpn) advanced option not working on flexy. ADDED: Flexy: it is now possible via the DO1Init ComCfg parameter, to configure the initial value of DO1 digit output of Flexy when it boots. ADDED: Support for Nagle algo bypass in openvpn version 8.2.s0 ------------- ADDED: Basic program can now be edited via the eWON web interface in a user friendly text editor providing eWON BASIC language syntax highlighting. FIXED: ioTag.getValueFloat32() function always returned "the ioTag format is not correct" FIXED: In MITSUFX IOServer, access to register D8000->D8511 on FX3 PLC type led to invalid addressing (and value). FIXED: In event log, ovpn (openvpn) was not part of IP communication event class FIXED: FLEXY: Watchdog occured when browsing in alarm history FIXED: COSY: MPI Profibus stations table was not loaded. FIXED: In the MELSEC IOServer, in UDP mode, when an error occured (timeout, invalid data received,..) the UDP socket was not closed, leading to possible socket leak. FIXED: Memory leak on Flexy when accessing the estat (or INF) block. FIXED: FLEXY: MPI reconnection shortly after disconnection to the same PLC could lead to eWON watchdog reboot. version 8.1s4 ------------- ADDED: Support for eWON other than Flexy and Cosy 13x for features above 8.0s2 version 8.1s3 ------------- FIXED: Writing negative values in a tag defined as float via SNMP lead to incorrect result in tag value. ADDED: The Tags' value, quality and alarm status can be refreshed automatically according to a user-specified refresh time in the eWON View I/O Section's Tag List FIXED: Flexy: Writing big values via SNMP leads to rounding error in actual value. FIXED: Flexy: When using Hitachi serial interface, eWON reboots when baudrate is 0 and topic is enabled FIXED: WIFI now correctly stops connection when AP is not reachable or down. FIXED: Very huge SMS sent by mobile operator could reset eWON FIXED: switching from WiFi to Eth as WAN source causing WAN missconfiguration FIXED: Invalid display for SSID with special characters. (could lead to html page error) version 8.1s2 ------------- FIXED: WIZARD: It was possible to display the trigger mode step page with Ethernet or WiFi selected on the Flexy CHANGED: eWON now checks its internet connectivity and public IP address on Talk2M instead of NoIp ADDED: WiFi: It is now possible to force the WIFI security manually (using Com config WifiSec parameter - default to automatic). FIXED: WIZARD: On Internet Explorer 9+ the LAN/WAN Configuration wasn't working properly FIXED: If we modified the current language in the COSY maintenance page it wasn't applied after reboot. FIXED: WIFI: Memory corruption when too many access points were present. FIXED: WIZARD: In the Cosy Internet Wizard the modem user and password were not taken into account properly FIXED: eWON was unable to connect to some access points (due to invalid security autdetection). FIXED: Before 8.1 eWON was working correctly with ASCII WEP keys, after 8.1 only HEX keys were working. eWON is now handling correctly HEX and ASCII WEP keys FIXED: Cosy: At language selection step on an empty Cosy the list of available languages could be duplicated several times if the user cancelled the login. version 8.1s1 ------------- FIXED: Flexy: with WIFI, the gateway and DNS appeared in the LAN configuration page. FIXED: Flexy: In eWON with WIFI and Ethernet WAN interface, the DNS and Gateway config could be cleared at reboot if Ethernet WAN is selected but DHCP is configured on the Wifi interface (although the Wifi WAN is not selected). FIXED: Flexy: when connecting the ethernet link directly to a device with ethernet sleep feature, the link could remain disabled until reboot. Typical when using direct cabled between eWON and recent laptop. version 8.0s2 ------------- FIXED: Upgrade with EDF when WIFI card in used was not possible. version 8.0s1 ------------- FIXED: Since rev 8.0 memory usage could leak if tag name case was different between tag definition and Basic tag usage. FIXED: Under high CPU load, the WIFI driver could crash and make the eWON reboot. FIXED: CAL was not working through M2WEB because of HTTPS proxying on M2WEB. FIXED: Cloud Accelerated Loading could get in trouble if 2 users accessed the eWON at the same time. CHANGED: Talk2M SMS Activation is now refused by the eWON if "Remote VPN WAN address or name" is set to "Talk2M Defined" to avoid erroneous eWON reconfiguration. FIXED: Wifi password was limited to 43 characters CHANGED: Modbus TCP client maximum number of simultaneous connections was increased to 32 (from 20) FIXED: Flexy could be upgraded with edf file in situation where a recovery was required FIXED: Tag helper was not accepting slot 4 for eWON IO's FIXED: Triggering hangup, if no outgoing action was pending since a configurable time, was not working any more since version 7. FIXED: In french web GUI, the Upload on alarm was missing in the data management configuration ?version 8.0s0 ------------- ADDED: port number in serial debug traces. ADDED: On Flexy, SMS reception and GSM reception update are now executed even if the PPP connection is active (modem is connected). ADDED: Tag Edition Helper added to IOServer configuration pages ADDED: Flexy PSTN extension card supported ADDED: Flexy WIFI extension card supported CHANGED: IOSERVERS: are not allowed to poll on the Ip address of the eWON itself CHANGED: On Flexy, when a Modem extension board is added or removed, the modem Init String is updated, ModExpType and ModFrcType are updated (according to new modem or no modem). CHANGED: ADSL Interface and Connection configuration pages have been merged. CHANGED: Incoming connection enable is not any more required to receive SMS with a GSM modem. CHANGED: Incoming connection enable is not any more required to receive SMS with a GSM modem.ADDED: "Cloud Accelerated Loading" feature CHANGED: Callback config not shown for modem without server capability CHANGED: Incoming connection enable is not any more required to receivADDED: When writing via SetSys Prg,"WANIP",X in Basic, where X is an integer. If X is 0, the WAN connection will be closed. If X is different from 0, then the WAN connection will be triggered. FIXED:MPI: When MPI baudrate was set to 0 unexpected errors/warnings were generated FIXED: S73 & 400 IOSERVER: improve Tag Address syntax validation FIXED: COSY: correct protocol type is now displayed after saving for ISTOCP to MPI/PPI gateway FIXED: Tree icons (+/-) were not consistent with tree status FIXED: When more than 20 SMS are received by eWON without beeing processed, the eWON could reboot due to corrupted memory. version 7.1s2 ------------- FIXED: Flexy: IsoTCP to Serial gateway was not working on flexy with serial (not MPI) interface. FIXED: Flexy: When Basic cyclic section was running the PPP negociation could fail. FIXED-CHANGED: Maximum number of tag fixed for Flexy: 2500, Others (CD,...); 1000. With more than 1000 tags on Flexy, intial boot produced "Queue full" errors and retentive values were not all restored. FIXED: Small memory leak when using the VPN and Talk2M CHANGED: eFive wizard affects now the WAN configuration by: Installing WAN filter (discard all traffic excepted VPN and initiated), block outgoing WAN traffic (except VPN), disable NAT. FIXED: Flexy: The VPN server address could not be resolved on a Modem connection. This did not impact Talk2M connections.REM: COM config parameter VPNPreDNS must be set to 1 on the Flexy (default value) FIXED: On Slow VPN Connection (GSM for example), the browser could receive pages with truncated end. FIXED: In case the 3G modem fails to respond during eWON power on, it will be hard reset. FIXED: Events from the VPN connection could be logged with a long delay. version 7.1s1 ------------- FIXED: Extention Boards compatibility check with firmware version. ?version 7.1s0 ------------- FIXED: in SMS sent by eWON with a @ character, all special characters after the @ are not converted to the GSM charset. FIXED: VPN was closed when changing anything in the configuration when connected to Talk2M FIXED: eWON will now correctly receive DHCP requests from the DHCP server on the WAN interface when WAN security is enabled (only improving RENEW request dialog, establishment was already working correctly) FIXED: Flexy: the eWON Energy IO Server "MaxInterval" parameter was not correctly configured to its default value FIXED: Max outgoing call duration setting was not taken into account when modem config AND using wizard FIXED: In Planner configuration, HTML characters were escaped in the messages (subject, message,...) CHANGED: Flexy: when initial language configuration selection is set to the default language (via web interface), the eWON does not ask to reboot the device. version 7.0s2 ------------- FIXED: When the "default com configuration" was selected via web interface, the config data was updated, but the new parameters were not applied. FIXED: JAVA: since Rev 6.0, when creating a SysControlBlock for a TAG record will either load an invalid value in "TagValue", or crash the eWON with invalid memory access. FIXED: SNMP was losing precision when using Coef/offset for reading or when writing big values via SNMP ADDED: better reporting when an invalid tag address is loaded. The message with tag name and address is reported in the event file. CHANGED: FLEXY: The maxium number of tag per IO server has been increased (from 500) to 1500 FIXED: Since rev 7.0s1, Home page did not always display the session information. FIXED: Writing to CIx (eWON IO Server) may corrupt eWON's memory. FIXED: Planner web page only displayed first 2 "Last Run". The estat file was correctly updated though. FIXED: eWON FTP server did not use correct port (20) for PORT command. FIXED: "Enter Slow Poll mode" not always reported since version 7.0 ADDED: eWON IO server tag naming extension for extension board validation. CHANGED: FLEXY ONLY: Config mem increased to 512K, Script increased to 256K. version 7.0s1 ------------- FIXED: Default Modem init string was not correctly managed in version 7.0. Clearing the init string did not put it to default either. Retirer du FW 7.0s0: ADDED: PROXY: Prevent Automatic proxy entries to connect outside the LAN network. ?version 7.0s0 ------------- FIXED: WIZARD: eWON could crash if Talk2M wizard was used with proxy but without authentication. FIXED: FINS IOSERVER: ParametersFinsEthClNode and FinsEthClNet are now displayed on the FINS ioserver web page even on a eWON with MPI. FIXED: REMOTE WIZARD: Remote wizard was not allowing shift from Free+ to eFive. FIXED: REMOTE WIZARD: Using the Remote Wizard to connect to an Endian/eFive server is now functional with other configured VPNPortOut values (not only 1194). FIXED: HISTORICAL LOG: Wrong record was added when topic wa enabled/disabled. FIXED: HISTORICAL LOG: Unwanted record was added when the TimeInterval was changed. CHANGED: IOSERVERS: Tags are disabled and reenabled only when Address, topicName,ServerName,ForceRO, Coef,Offset,Type or Autotype configuration parameters are changed. FIXED: WEB PAGE: Charset not force any more of /usr defined web pages. FIXED: SERIAL: eserial-IO driver read was produced randomly when the ioserver configuration was changed due to close and reopen serial port. FIXED: ABLOGIX IOSERVER: IOsend/IORcv was not working on ethernet. FIXED: ABLOGIX IOSERVER: Destination DF1 address configuration parameter was not working. FIXED: ABLOGIX IOSERVER: Ioserver was producing error 'CIP reply with unsupported tag type" during ftp operation. FIXED: VPN: user/pwd mode: Changing account was requiring a reboot. FIXED: MITSUFX IOSERVER: Critical error was occuring when user reboot was initiated and MITSUFX ioserver was enabled. FIXED: SNMP IOSERVER: Disabled tags in errors mechanism is working now. FIXED: SNMP IOSERVER: Topics disabled are not reading anymore,and different topic requests are not merged anymore. FIXED: DF1 IOSERVER: Using eWON Tag Type DWORD with SLC500 N (integer) register was producing wrong reading if value is above 32767. FIXED: MODBUS IOSERVER: Modbus Status Tag was not reflecting status of RTU device when a tcp/rtu gateway is used. FIXED: S73&400 IOSERVER: First commmunication using MPI does not produce anymore the "MPI-Write failed" error. ADDED: MITSUFX IOSERVER: Serial baudrate for FX3U PLCs is now configurable up to 115200 bps. ADDED: WIZARD: eFive: Add a UDP/TCP combo and a Port entry field. ADDED: MELSEC ioserver: Add ability to poll FX3U and Serie A PLCs. ADDED: PROXY: Prevent Automatic proxy entries to connect outside the LAN network. ADDED: ALARM: It is now possible to define user templates for SMS and EMAIL tag alarm notification. ADDED: eWON COSY: Add Talk2M Connectivity test to COSY devices. ADDED: WANMGT: Add failover from WAN ethernet to 3G upon reception of a "talk2MConnect" SMS. CHANGED: SERIAL: For serial ports which can be configured in half and full duplex mode, the ports are set to full duplex at boot time. ADDED: JAVA: add HTTP client. ADDED: DF1 IOSERVER: reading registers for data type L (micrologix) is now implemented. ADDED: CONFIG: It is now possible to delete a user by using the same technique used for tag (ie: using the DoDelete field set to 1 when importing or via Basic/Java). FIXED: WIZARD: The Test Talk2M Cnx button must not appear before wizard was executed once. ADDED: WIZARD: Option added in T2M wizard to skip the UDP connection test. version 6.4s7 ------------- same as version 6.4s6 version 6.4s6 ------------- ADDED: eWON500V2 and eWON4001V2 now provide Java support. CHANGED: All references to Endian have been replaced by eFive. FIXED: When VPN was enabled and WAN was not accessible (invalid gateway) the eWON was locked until full reset was executed. FIXED: Endian/eFive Wizard result were not updated and seemed to run forever though wizard was finished. FIXED: In some cases, the eWON could reboot due to a watchdog when the VPN connection was openned. version 6.4s5 ------------- FIXED: corrupted memory when VCOM was reconfigured. Caused eWON to reboot. CHANGED: When an error occurs in Talk2M mode during VPN establishment the vpn process exists (avoid crazy loop for DNS resolution) CHANGED: Talk2M address acquisition mechanism now uses ip and name (according to what server sends) CHANGED: Endian wizard logo changed to eFive logo. CHANGED: VIPA logo updated. version 6.4s4 ------------- FIXED: When a /usr file was exported using an export block descriptor, and the file ends with a < or a <% character, the export remained pending until a watchdog occured. This was true even if the NOSSI filter had been specified. FIXED: Sending SMS via GSM resulted in memory corruption since version 6.4s0 FIXED: MELSEC IOServer: It is now possible to poll on devices where Network ID <> PC ID CHANGED: InfoZ protocol update according to server change ADDED: The SNMP IOServer can now read STRING type OID and will convert their content to float. version 6.4s3 ------------- FIXED : DF1 IOSERVER: DF1 polling was not restarted automatically anymore after reboot. Regression since release 6.4s0 FIXED : UNITE IOSERVER: Unitelway polling was not restarted automatically anymore after reboot. Regression since release 6.4s0 FIXED : S2700 IOSERVER: PPI polling was not restarted automatically anymore after reboot. Regression since release 6.4s0 FIXED: S73&400 IOSERVER: Default Rx/Tx Timeout parameter is now also applied on ISOTCP requests FIXED: EMail password was not sent in UTF8 format. This may affect users who authenticate against their mail server and use non ASCII chars in their password. CHANGED: eWON IO server priority has been increased to improve eWON counter latching interval precision. CHANGED: If VPN is configured for Talk2M and connection has failed for 2 days (since end of last connection success), and connection has failed at least 10 times, and wizard has been executed in automatic selection mode (UDP or TCP), and no proxy is configured, then the connection test wizard is executed in unattended mode to try and recover communication. FIXED: When export block descriptors in TEXT mode were attached or included into emails, the last line was omitted. CHANGED: VPN cannot be disabled any more even if configuration is invalid. FIXED: When the "Talk2M connectivity validation" wizard was executed, the WAN configuration parameters were reset to the Talk2M wizard values. They don't need to be reset if they have been tunes after Talk2M wizard execution. ADDED: JavaVersion item was added to the estat ($dtES) file. JavaVersion reflects the JavaEtk version in the eWON. From the Java program, the same information can be read by using the System.getProperty("ewonitf.version") command. FIXED: Tabular config edition does not work for not ASCII characters (intl. languages). The System wizard in eWON Cosy is also impacted (eWON name for example). CHANGED: The FTP and SMTP passwords are now encrypted in the configuration file and hidden during web edition. FIXED: in case of VPN configuration error, eWON will increate the delay between retry up to 5 minutes but without never giving up. After a reboot, to retry period is reset. ADDED: in eWON Cosy, When the digital input is used to allow or prevent the WAN connection, a trace is logged in the events file when its state is changing CHANGED: eWON Cosy: Internet connection wizard wording changed to avoid user's confusion. ADDED: eWON Cosy: Date and time is displayed in footer on every status page with a refresh rate of 10 seconds ADDED: In javaetk 1.3: Tag management can be programmed by events. Four new listener configuration methods: addTagValueListener, setDefaultTagValueListener, addTagAlarmListener , setDefaultTagAlarmListener version 6.4s2 ------------- CHANGED/FIXED: Prevent VPN from being disabled even in case of multiple configuration error. version 6.4s1 ------------- ADDED: It is now possible to edit the configuration in a tabular form via the storage configuration in the system menu. ADDED: The Talk2M wizard has a new option for checking connectivity without updating the Talk2M keys. FIXED: MITSUFX IOserver: tag type INT can now be used without errors. The Problem was present in the eWON firmware since release 6.0 ADDED: Framework for remote wizard via eBuddy (this is internal feature that needs an eBuddy update to be used) FIXED: Watchdog : When the IOServer-Global TCP RX/TX Timeout was set to a value less than 1000 Msec, the eWON crashes due too EIP software watchdog FIXED: MITSUFX IOserver: Float Data registers are now read and written correctly FIXED: eWON Cosy: the EIP gateway comment was not correct in web page. FIXED: When save config.txt in an eWON 4x02, the VCOM config for ports 2 and 3 was not exported. ADDED: Reboot button was added to the eWON Cosy maintenance page. CHANGED: Internet connection wizard will not erase configuration by default. A warning message says that Talk2M config will be erased also if to erase option is chosen. FIXED: SMTP: The Second email was not sent out after a fist email was sent out immediately followed by an SMS sent out, and a second email to send out. FIXED: Tag Values scale & offset use: Regression since 6.0, boolean type tags were read without taken into account coef and offset. This was not the case in previous release version 6.4s0 ------------- FIXED: Browser cache not operational due to date format change. Performance impact. FIXED: NTP: when enabled NTP will not wait next reboot anymore to start time synchronisation ADDED: BASIC: add proxy feature to PUTHTTP and GETHTTP commands FIXED: UNITE IOserver: The eWON UNITE IOServer did not allow polling of the last 7 bits of the Internal Data bits section ADDED: IOservers: add a new trace message to inform if IOserver configuration when at least one its topic is enabled. FIXED: DF1 IOserver: IOSEND/IORCV BASIC commands didn't work on ethernet link FIXED: MELSEC IOserver: cosmetic mistype error in request refused by server error message FIXED: MELSEC IOserver: IOSEND and IORCV BASIC commands didn't correclty work when used with the MELSEC IO server. FIXED: Out of memory reboot error could occur in some special case when using the JAVA WebProducer.escapePath function. FIXED: MELSEC ioserver: eWON was rebooting (watchdog) when destination address device was unavailable or not existing FIXED: When exporting $dtHL in Binary mode ($ftB)with an end date specified ($et) AND the end time is inside to data present in the eWON file system, then the file exported is truncated at the end by an amount of max 96KBytes for eWON firmware >=6.0s2 and max 8KBytes for eWON firmware <6.0s2 FIXED: When writing SNMP tag from the SNMP IO Server, when communication problem occured, the eWON could reboot with an "Bad address in dynamic memory management" error. This only occured while writing tags, not while reading SNMP tags. FIXED: MELSEC IOserver: MELSEC IOServer was not reading correctly the end of bits zone FIXED: Proxy was not working on FTP protocol, passive mode, entering on the WAN interface when WAN is an embedded ADSL modem. ADDED: WEB page: cosmetic: message "Reboot required if change" on the ModemSetupPage has been added to warn the user that the WirelessNet param needs a complete modem reset to be effective FIXED: SMS: sending SMS with accentuated characters are not generating errors anymore version 6.3s0 ------------- FIXED: When ADSL is available, the WAN connection is set ADSL in the default config and "maintain connection" has been disabled by default. FIXED: With UMTS modem, an operator could appear 2 times in the list. Duplicates are now filtered. FIXED: JAVA: The socket error code return was 1 in case of error while it should be the low level IP stack error code. CHANGED: SNMP thread watchdog delay has been increased to 40sec to avoid spurious reset. ADDED: S73&400 ioserver: new feature: MPI polling and gateway for PLCs located on a remote MPI subnet. FIXED: with some SIM cards in an eWON with a UMTS modem (xx01CD), the modem reported a SIM ERROR though the card was valid and working. FIXED: SMS cannot be received on HSUPA rev 2.4 ADDED: MELSEC ioserver: allows tag polling on ethernet interface of the MISUBISHI Q series ADDED: GsmWLessNet value returned in INF (estat) block to report actual wireless network detected (if known) CHANGED: "Too much global memory allocated" critical error condition has been removed as the eWON always reboots when it has an memory alocation problem. FIXED: When the error "The SMS in the SIM card could not be read because too many present" was reported, a memory corruption could occure. FIXED: When serial debug was activated and packets of more than 242 bytes were sent or received at once it could lead to memory corruption (illegal memory address or dynamic memory critical error reboot) FIXED: on eWON with 3G or HSUPA modems, the Hardware watchdog was sometime triggered. The eWON was rebooting with an Hardware watchdog error message. FIXED: On eWON with an ISDN modem, the init AT string must contain the &D2 command. This is NOT applied eWONs previous to the CD familly as these modem do not support the hard DTR hangup mode. FIXED: S73&400 ioserver: MPI 12Mb bus desynchronisation problem solved FIXED: viewIO Graph: non float values were not displayed correctly anymore. Regression since 6.2s0 FIXED: PLANNER: does not anymore generate SMS with text "action:" followed with uninitialised text. Was causing illegal memory access. version 6.2s1 ------------- FIXED: The Internet connection wizard did not set correctly the connection trigger type when using modem for internet connection. The modem internet connection was set to permanent (since 6.2s0 only). FIXED: during Talk2M wizard, the WAN options changes were not applied if WAN connection was active during Wizard execution. version 6.2s0 ------------- FIXED: the tag type was not correctly stored in ircall.bin file CHANGED: If the eWON has an ethernet WAN connection, then the WAN permanent connection is enabled in the default configuration. The WAN Ethernet connector led will be blinking by default after a full reset (though the connection does not default to DHCP to avoid error burst in case no cable or DHCP is present). CHANGED: When the Talk2M wizard is executed, the following configuration parameters are set: WAN interface protection allows only VPN and return traffic, No forwarding from VPN or LAN is allowed to WAN interface, and NAT interface configured to NAT on LAN (Plug'n Route) ADDED: The NAT module also works on PING messages passing through the NATed interface.These return messages will pass even if the 'Block ICMP' option is selected. ADDED: NAT can now be installed on LAN interface in order to route traffic to devices on eWON LAN without setting the eWON as gateway in the device (this is only applicable when VPN is used). ADDED: It is now possible to filter who can access what on the VPN based on the VPN source address (can be used to grant access to specific resources on the eWON and LAN based on eCatcher's user IP address). FIXED: TALK2M: With eWON-GPRS, when the eWON was OnLine on Talk2M, and we sent it offline from eCatcher, the eWON was well disconnected BUT the VPN was restarted too quickly and was staying running indefinitely. ADDED: WIZARD: when the Talk2M wizard is used with the Talk2M free+ server, and the eWON serial number is already defined in Talk2M (other eWON name and/or account), following warning is displayed:"The eWON serial number was already defined in Talk2M. Previous instance was disabled" ADDED: S73&400 IOSERVER: mpi advanced bus parameters are now made configurable ADDED: MODEM: allow more than 4 digits for the PIN code FIXED: eWON configuration by SMS for Talk2M was not working on the Free+/Pro server. FIXED: TALK2M: If the 'Remote VPN WAN address or name' paramter on the eWON was set to "talk2M defined" then eWON was restablishing the Internet connection +- 3 minutes after receiving the Talk2M connection request (Talk2M wake-up SMS). ADDED: redmine 1515: mode Hangup using DTR will be used for all eWONs with ISDN except PCode 74,68 and 86 FIXED: viewIO Graph: float values were not displayed correctly anymore: values rounded. Regression since 6.0s0 FIXED: OPENVPN: default renogiation time set to 86400 sec FIXED: OPENVPN: during key renegotiation, the vpn process is set to low priority CHANGED: The No-Ip request to obtain our own IP address is now sent on the 80 port instead of 8245 for better compliance with firewall rules ADDED: BASIC: ERASE command is now also used to format the /usr and the /sys partition FIXED: DF1 ioserver: when an unregister session message is received on eip the associated socket has to be closed. This was causing a reboot of ewon due to critical error. FIXED: MODEM: Modem Init String was truncated when quotes are used inside the string ADDED: MODEM: Mode Hangup using DTR will be used for all eWONs with ISDN except PCode 74,68 and 86 FIXED: RWIZARD: remote wizard was not working on modem connection version 6.1s2 ------------- FIXED: the account name was not saved when using wizard for new talk2m when registration was done using account/ewon/user/pass CHANGED: if the internet connection wizard test fails only because of the online IP check, the config is nevertheless applied. ADDED: The eWON sends its LAN IP address and mask during Talk2M wizard to help eCatcher to apply correct routes. CHANGED: The talk2m wizard only asks for an account name in case the new Talk2M service is selected and the activation is using eWON name, username, password version 6.1s1 ------------- FIXED: The internet connection wizard was broken when used on the WAN interface FIXED: The new VPN WAN proxy configuration page had an blank combo box in DE and FR languages version 6.1s0 ------------- CHANGED: The Talk2M wizard has changed to default to Talk2M Pro, Go, Free+. It can though fallback to the old Talk2M Free configuration. FIXED: UNITE ioserver: Boolean tags were not read correctly anymore (release 6.0 regression problem) CHANGED: It is now possible to update the VPN proxy configuration manually via the VPN/Global configuration page. FIXED: S7200 ioserver: Download of a PLC program was not working on a PPI slave PLC when a PLC master was also communicating on the same network with the slave PLC. Retry mechanism added at protocol level. CHANGED: Talk2M VPN server address acquisition now defaults to automatic to comply with Talk2M scalability requirement. CHANGED: Label added under the Wizard button for clarity. FIXED: Talk2M wizard: Increase of the VPN establishment timeout to avoid valid situation timeout failures. FIXED: MODBUS ioserver: UnitID 0 is now allowed for polling purpose CHANGED: Proxy configuration during Talk2M wizard is now "protected" by a checkbox for clarity CHANGED: When the Talk2M wizard is executed, it will only test an UDP or direct HTTP connection IF the HTTP proxy address is empty.For Basic or Java driven wizard, the UDP or HTTP direct connection will be tested regardless of the HTTP proxy address IF the connection type is forced (to UDP or TCP). CHANGED: The PCode 41 has now the VPN feature enabled (changed from 2001CD MPI to 2101CD MPI) FIXED: eWON was not correctly reading the VPN server address before connecting to Talk2M pro server. It was thus using the address received during wizard execution. FIXED: modem: WAVECOM modems were not detectable anymore when they are configured in monoband FIXED: WANMGT: after a ppp connection close, ppp was opening again only after 2 permanent wanmgt restart trials. (regression occured in 6.0s0) CHANGED: During the "Configure INTERNET Connection" wizard, if the WAN connection is set to "Ethernet", then the wizard skips the "Trigger online connection" configuration and "Maintain connection" is automatically configured. FIXED: BACKUP: EWON does not reboot anymore with the event "Relock more resource" at second ebuddy backup.tar restore trial FIXED: MEM IO server: RET booleans tags get wrong values when upgrading to 6.0 (regression since 6.0s0). FIXED: java: The function "EventManager.logEvent(msg, value)" was only accepting values from 0 to 100 corresponding to ErrorEvents. "Java" event code support has now been aligned with the "basic" one: [0,99]: range for error message, [-1, -99]: range for warning messages, [100,199] for trace messages. version 6.0s3 ------------- ADDED: Internal behavior to change Q2687RD and make it respond as a Q2687 FIXED: transfer of inst_val.txt to the eWON was crashing the device (illegal memory access) CHANGED: the button hold time has been reduced from 15 seconds to 4 seconds to simplify the full reset procedure FIXED: The HSDPA modem init string was changed to comply with modem firmware upgrade. FIXED: Data management password was not displayed in the configuration web page and was lost when the config was updated. version 6.0s2 ------------- FIXED: The hidden "downgrade only" right was not working. FIXED: Read Mbs TCP header error could be reported if timeout was <=1000 msec for modbus. FIXED: BASIC: since release 6.0 ON CHANGE action was executed twice when the TagValue was changed. FIXED: ABLOGIX, DF1 ioserver: gateway and ioserver functionality are disabled when the EIP port is configured with a 0 value (need reboot to be applied). An additional error message "EIP port is disabled" has also been defined and is displayed in the event file when eip polling is active for one of these io servers but the eip port is configured to 0. By default eip port is still 44818. FIXED: VPN: reduce VPN establishment CPU power consumption to let other processes run. FIXED: WEB VIEWIO page: When the initial portion of the value entered is not an integer nor a float, the tag value is not updated and the error message "invalid value" is displayed. FIXED: IOSERVER: scaled values (coef and offset are taken into account) are now displayed even when historical logging is enabled.Regression error since release 6.0so FIXED: Historical table: size increased to allow up to 500 tags with a name length up to 50 characters to be showed FIXED: EWON ioserver: does now work with oem release. version 6.0s1 ------------- ADDED: eWON can now be configured to request authentication to change IP address using eBuddy (you need eBuddy>1.8 to use this) ADDED: WEB SERVER: support of Access-Control-Allow-Origin header echoing back the same origin that was sent or * FIXED: WANMGT: If the "Connect WAN required to reach" is triggered just after the close of the PPP connection, then eWON try now to establish the connection again. FIXED: ABLOGIX IOSERVER :selection of bit 31 of DINT tag types is now working FIXED: SMS: not well formatted SMS are now erased from the SIM card FIXED: SMS: TAP PROTOCOL: eWON wait to receive a >CR> to ensure compatibility with old TAP servers (prior to version 1.6) FIXED: EXPORT: Supported size of the entries of the Historical table has been increased to 8Kbytes to avoid export failures due too buffer too small FIXED: ABLOGIX ioserver: it is now possible to read a register of type real FIXED: eWON ioserver: AI tags are now working on the eWON 4002 FIXED: flash access regression problem which appear on release 6.0S0 is now solved version 6.0s0 ------------- ADDED: eWON supports now Tag Quality. ADDED: eWON now supports Integer and Dword Tag types. FIXED: When HSDPA modem needed to be hard reboot, the hardware reboot function was inefficient. ADDED: A "hidden" user right with value 2048 has been added the the existing set. This right only allows user to downgrade (with dewonfwr.edf), but not to download an ewonfwr.edf file. ADDED: When on alarm is defined in Data Management, the eWON will trigger a DM transfer if one of the tag belonging to one of the group defined in DM config enters the alarm state. ADDED: Filter feature for data management is working now. ADDED: The $dtHL (Historical logging) now supports the $fl exactly the same way $dtHT does. This feature applies to text and binary format. FIXED: In the SNMP IOServer, if the same OID existed with different IP addresses, the IOServer was not working correctly. CHANGED: IPSTACK: IPCP TIMEOUT has been set to 5 sec FIXED: MDEX VPN configuration was not saved correctly to comcfg.txt ADDED: In Comcfg.txt, a new parameter called "KillLAN" has been added for the very special case where you need to close the eWON LAN interface forever. In case this parameter is set to 1, you will need a Level 2 reset the return it normal (or through WAN interface if available). FIXED: no need to reboot eWON any more to take ADSL configuration into account. FIXED: DMSync could not transfer data to VPN with a GPRS modem because VPN was not established before the transfer started. CHANGED: The data management menu is now enabled in every eWON having the historical logging feature. FIXED: S7200 IOSERVER: TagStatus with the destination at the TagLevel is now supported FIXED: UMTS modem could be lost in case an invalid comcfg.txt was downloaded in the eWON (requiring tricky VCOM operations to recover modem) FIXED: FTP: restore of config files containing variables with values length higher than 2048 bytes is now supported ADDED: Basic command SETSYS PRG,"ADSLRST",1 has been added to force a reset of the ADSL modem. CHANGED: ADSL status is now monitored even if there is no user or password configured. ADDED: in INF export block, the "ADSLLocRemSNRTxt" and "ADSLUpDnSpeedTxt" have been added to provide the Signal noise ratio and the upload/download speed for ADSL FIXED: FTP server: LIST command is now working when using GPRS FIXED: anonymous connections to FTP server using eWON FTP client were impossible. version 5.7s4 ------------- FIXED: S7200 IOserver: PPI MULTIMASTER mode was not working anymore on the eWONs with MPI port FIXED: VCOM: add an extra parameter to configure vcom buffersize in order to improve vcom communication (eg: LOGO) FIXED: WIZARD: cosmetic error: change error message to ""Can not apply internet config" when an incomptiable WAN LAN IP range is configured FIXED: MPI: eWON was not recovering anymore automatically from the OFFLINE state when the go offline reason doesn't exist anymore version 5.7s3 ------------- FIXED: It was impossible to register on the network with a xx01CD with Quad band GSM (and SIM is PIN locked) - Since version 5.7s1 version 5.7s2 ------------- FIXED: Introduction of HSUPA modem support introduced a bug that prevents registration of the PIN code in the Modem. The GSM modem was unusable. version 5.7s1 ------------- FIXED: Software reboot of xx01CD GSM did not work on Telit modems. FIXED: S7200 IO server: Large programs are now successfully download in case of large programs through ppi serial FIXED: When the MPI chip (in PPI mode) goes into "Offline state" due to an external condition, the eWON tries to restart it automatically. ADDED: LAN, WAN IP compatibility: At wizard level check if a static IP is requested if range maches the LAN range and generate an error message. At interface activation level, refuse compatible ranges and save an error message in the events log FIXED: HISTORICAL TABLE: When a filter is applied and no interval is specified for the historical table, the output time is specified by the records of the tags belonging to the filter FIXED: BASIC: ON CHANGE: When a critical definition field value of a given tag is changed, the ONCHANGE basic actions are not loosed anymore. Furthermore SNMP publication field values are added to these critical field list. Finally, The IOMOD command returns now only TRUE when the tag value has been changed. FIXED: SNMP IOSERVER: cosmetic error on config web page (OID may not be set to 32-bits but is limited to 16) FIXED: ALARM: alam retrig and retry mechanism were not working correctly. Retrig mechanism is now permanent and may be put to zero (no retrig). It does only apply to ALM events FIXED: SNMP IO SERVER: error message is now displayed when a a not supported type was returned by the snmp agent FIXED: EXPORT BLOCK: historical table: an error was displayed when no format option ($ft) was specified FIXED: WIZARD: configure internet connection on WAN wizard does not need reboot anymore FIXED: ALARM: on translated pages, a ASP2HTML sentence was added to content of file, trap and alarm subject. FIXED: VCOM: Error message "gio-Server Name request does not exist" was still displayed without presence of real error UPDATED: WIZARD: Talk2M wizard forces the "Remote VPN WAN address or name" to "defined Manually" when wizard is used for Talk2M free. FIXED: PLANNER: attachement of export block to email is now working FIXED: MODEM: add a check upon OperatorId length FIXED: MODEM: increase error level of modem read error from warning to critical. FIXED: S7200 ioserver: download of large programs on MPI port ADDED: New HSUPA modem for eWONx005CD FIXED: SMS: check added to verify that only REC READ or REC UNREAD messages are present on the card. When it is not the case a cleanup of the sim card is executed. ADDED: TAP protocol compliance improved when closing the communication with the server (No evidence of problem with previous implementation). version 5.7s0 ------------- ADDED: BASIC: ERASE command has been extended in order to allow deletion of history file (hst_alm.txt, events.txt, ircall.bin) FIXED: eSyncDM: data transfert scheduling was not working ADDED: BASIC: add ON DATE basic command to perform basic actions on a given time interval. ADDED: PLANNER: add web configurable planner to allow execution of unconnected actions (send EMAILs, PUT FTP, send SMS, send SNMP TRAPs) on a given time inteval. ADDED: BASIC: a new Fieldname "SCHRST" has been added to the PRG group of the SETSYS command to clear pending actions. Syntax: SETSYS PRG,"SCHRST",1 FIXED: Tag Alarm Page: wrong example was displayed FIXED: WIZARD: cosmetic: reset buttons replaced by reboot buttons FIXED: SNMPIO server: Status was not working when s address was specified at tag address level. FIXED: VPN: VPN connection was closing when a new var_lst.csv was PUT on the eWON using FTP. FIXED: PPI multimaster: download was not working on eWON MPI FIXED: MDEX support was improved by supporting the redirection. The user can now click on the MDEX dashboard link to access the eWON web page. FIXED: MODBUS IOSERVER: after a UnitID 255 is configured at topic level on the iosever page , general config page updates and basic save operation do not fail anymore FIXED: Some configurations could not be reloaded in newer firmware. Config memory size now reflects actual saved data. Each tag and users requires an additional amount of memory that was allocated on the 256KB config memory. FIXED: JAVA: FileConnection.rename function is now working FIXED: MODBUS IOSERVER: The Advanced Parameter "TcpPort" to define the port (<>502) used by the ModbusTCP clientwas not functionning SINCE 5.2s0 ADDED: TALK2M: Wake up SMS string "Talk2MConnect" has been added besides "Talk2M_Connect" to avoid problems on some mobiles. ADDED: Remote wizard: feature used to trigger wizard execution without using the web interface but through the use of a remote wizard file containing all needed parameters. This feature can be used for secure talk2m server switch over. ADDED: S7200 IOSERVER: Extension to the PPI protocol in order to support multimaster mode. By default multimaster extension is not enabled. CHANGED: When loading the BASIC program, the eWON checks it for any corruption and tries to fix it if found. ADDED: a wizard was added to connect to MDEX more easily. FIXED: possibility to write a string to viewON with $script$ ADDED: wizard rollback: Communication parameters configured through the wizards (and remote wizards) will from now on only be saved in the flash in case of success of wizard execution. In case of failure, the old communication configuration parameters will be reloaded from the flash. This feature can be used for secure talk2m server switch over. ADDED: wizard rollback: Communication parameters configured through the wizard (and the remote wizard) will only be saved in the eWON flash in case of success of wizard execution. In case of failure the old communication configuration parameters will be reloaded from the flash. This feature can be used for secure talk2m server switch over (t2mCnx: wizard). FIXED: Configure internect connection wizard: PIN code change is now applied (modem reset) FIXED: JAVA feature was missing in eWON 4102. FIXED: S7-200 IOserver: Disable tags in error is now working for the S7-200 ioserver. ADDED: S7200 IOSERVER: advanced S7200 parrameters are added to the S7-200 Ioserver configuration page FIXED: VCOM: When an update without changes was done on the VCOM web page a vcom_TCP bind failed event appeared in the events.txt section and reboot was needed to release the port FIXED: VCOM: When a serial port was opened using VCOM and the STOP IOServer option was configured, the error message "gio-Server Name request does not exist" was written in the event file even when no ioserver was configured FIXED: GSM MODEM: modem detection problem was occuring when too much network operators where present. FIXED: BASIC: precision is not anymore lost during integer multiplication FIXED: PUTHTTP: when an empty response "" was given as argument to the PUTHTTP basic command, the command was reporting an error even in case of success. ADDED: BASIC: ERASE command has been extended in order to allow deletion of history file (hst_alm.txt, events.txt, ircall.bin) FIXED: eSyncDM: data transfert scheduling was not working ADDED: BASIC: add ON DATE basic command to perform basic actions on a given time interval. ADDED: PLANNER: add web configurable planner to allow execution of unconnected actions (send EMAILs, PUT FTP, send SMS, send SNMP TRAPs) on a given time inteval. ADDED: BASIC: a new Fieldname "SCHRST" has been added to the PRG group of the SETSYS command to clear pending actions. Syntax: SETSYS PRG,"SCHRST",1 FIXED: VPN: VPN connection was closing when a new var_lst.csv was PUT on the eWON using FTP. FIXED: PPI multimaster: download was not working on eWON MPI FIXED: MDEX support was improved by supporting the redirection. The user can now click on the MDEX dashboard link to access the eWON web page. FIXED: Some configurations could not be reloaded in newer firmware. Config memory size now reflects actual saved data. Each tag and users requires an additional amount of memory that was allocated on the 256KB config memory. FIXED: MODBUS IOSERVER: The Advanced Parameter "TcpPort" to define the port (<>502) used by the ModbusTCP clientwas not functionning SINCE 5.2s0 ADDED: Remote wizard: feature used to trigger wizard execution without using the web interface but through the use of a remote wizard file containing all needed parameters. This feature can be used for secure talk2m server switch over. ADDED: S7200 IOSERVER: Extension to the PPI protocol in order to support multimaster mode. By default multimaster extension is not enabled. ADDED: a wizard was added to connect to MDEX more easily. FIXED: possibility to write a string to viewON with $script$ version 5.6s3 ------------- FIXED: When the eWON was configured for outgoing VPN, and it was using PKI (not shared key), and the Keep Alive interval was longer than 60 seconds and 2 remote VPN addresses were defined, then the eWON did not toggle between remote addresses when the first one failed. ADDED: The $dtSS file and INF Basic bloc now includes an additional value called GsmCCID, it contains the SIM Card Identification Number if available. ADDED: VCOM: when a VCOM client connects MITSUFX, HITACHI and S5-AS511 ioservers will be stopped if they use the same serial port. When VCOM disconnects, they will restart again.This feature is enabled by checking the Stop IoServer entry on the COM virtual page configuration. This feature is disabled by default. FIXED: S7200 ioserver: multimaster PPI IO server was entering in slow poll mode when the PLC was high loaded ADDED: Idle PPP connection was only checked against incoming IP packets. It is now possible to monitor inactivity based on outgoing IP packets also. FIXED: When clearing the Talk2M Access Server Address, the eWON returns to the Talk2M Free EU server. The wizard now also allows to select the Free or Pro server. FIXED: s7200 ioserver: eWON was displaying an error message when it polled the last register of a register type FIXED: S7200 ioserver: didn't allow to poll more than 50 tags belongin to the same type of register FIXED: Static route entries were not working when gateway was using WAN interface since the WAN interface is dynamically disabled. FIXED: JAVA getWanIp was blocked during up 60 seconds when connection establishment was in progress. FIXED: Historical recording intraSecCounter was not updated. CHANGED: When multiple alarm actions (SMS, EMail,..) are defined for an alarm, the SMS is sent first followed by the others, this prevents PPP from being disconnected after PPP IP address has been published by mail (for example). CHANGED: Cosmetic change is example on S7-3&400 configuration page: TSAP added to ISOTCP syntax example. CHANGED: Cosmetic alarm configuration page change. SMS example now show 2 recipients FIXED: In Basic, the GetSys xx,"Parm:SubParam" command ended with a watchdog if SubParam was empty. ADDED: In WAN security configuration, it is now possible to prevent traffic forwarding from LAN to WAN. ADDED: The eWON can authenticate through an NTLM proxy when connecting to Talk2M. During the Wizard execution, the eWON will detect the correct authentication and configure it for further connection using OpenVPN. ADDED: JAVA: IoManager.getNbTags function. FIXED: MPI status was not reflecting the communication status. MPI status led switched not to OFF when the cable was removed FIXED: Any on demand action that required the VPN to be established to take place could fail because they were triggered after WAN was established but not after VPN was established. ADDED: when the activation key starts with US, then access server is configured to Talk2M Free US and the activation key prefix is removed before activation (allows SMS activation) version 5.6s2 ------------- ADDED: BASIC - Extended syntax to handle lists of parameters ADDED: BASIC - EOF for export blocks ADDED: BASIC - All Tag-related functions now accept the tag's name, ID and index as reference ADDED: BASIC - GETSYS PRG,"NBTAGS" returns the number of tags ADDED: BASIC WOY() function (Week-Of-Year - ISO8601) ADDED: BASIC - RENAME function ADDED: SNMP IO Server FIXED: In some cases when an error during OpenVPN start, the VPN was never restarted again until a reset occurred. FIXED: typo error in PPP server configuration page. FIXED: When the eWON's VPN process stopped on a fatal error, it could not restart and displayed an "Out of memory" error or a "Cannot open TAP" error. This error was common when using the eWON in conjunction with an Endian firewall. FIXED: The DHCP timeout parameter (DhcpTO) defaults to 45sec but it was not taking into account values higher than 60sec. It is now possible to increase to timeout up to 240sec. CHANGED: Some "memory information fields" are now displayed in bold when more significant. FIXED: when the VPN was actively negotiating a connection and the user tried to update the COM configuration, the operation could failed and a "write file operation failed" could be logged in the events.txt file. ADDED: Embedded ADSL upgrade engine. It is now possible to upgrade the embedded eWON ADSL modem. ADDED: ADSL Watchdog mechanism. In case the modem does not respond any more it will be hard rebooted. FIXED: ADSL Modem BOOT timeout was increased to 80sec (instead of 45). ADDED: Support for Q26 GSM/GPRS modem upgrade. ADDED: modem upgrade requested can now be configured from the "eWON reboot page". version 5.6s1 ------------- FIXED: Implementation of the EnableChunkEncoding com parameter FIXED: FTP upload of inst_val.bin did not work. CHANGED: Default mode for web server is set to "Chunk encoding" disabled. CHANGED: eWON Skin customization now includes the product name also. CHANGED: Redirect all traffic through VPN now works even if no gateway is defined on the eWON side (Proxy configuration or local LAN for example) CHANGED: When VPN connection occures through proxy, the eWON will now accept the 'route all traffic through VPN' option (it was previously ignored). FIXED: VPN server address request for Talk2M Pro did not work when VPN configured through proxy. FIXED: in some case is was impossible to read back the ComCfg.txt (though HTTP or FTP), the eWON rebooted with an 'out of memory' error. FIXED: When the Talk2M wizard was executed, the VPN key was not encrypted in the config file until another field the configuration was changed. FIXED: After configuring the eWON with Talk2M, the comcfg.txt contained an invalid key format (line feeds in the comcfg.txt file). When the configuration was edited, the problem disappeared. CHANGED: if ModExpType<>0 and ModFrcType:0 in the comcfg.txt file, the eWON will power off the modem. A trace in the events.txt file confirms the operation. ADDED: in the JAVA t2mCfgCommand and additional parameter can be used to select the Talk2M connection mode during connection wizard execution. ADDED: BASIC in the SetSys PRG,"T2MCFG",... command an additional optional parameter can be used to select the connection mode during Talk2M configuration wizard. ADDED: 2 commands added to JAVA: IOManager.modemLedJvmCtrl and IOManager.setModemLed, provided to control the Modem led through the Java program. ADDED: The eWON firmware is now able to reflash the ADSL modem firmware by putting the ADSL firmware file in the eWON /usr directory and configuring the BootOp parameters. version 5.6s0 ------------- FIXED: The "Hang Up if no action" timer was no initialised when a new outgoing connection occured. In case an outgoing connection occured without outgoing action (callback for example), the timer thus expired immediately, closing the connection. FIXED: The Proxy External interface combo does not show VPN any more for eWON without VPN. ADDED: config.txt HTTP_REQTO advanced parameter for setting the HTTP server watchdog interval. Used for lengthy request in ASP, or SSI pages. ADDED: Added support for Telit HSDPA modem ADDED: JAVA getT2mCfgInProgress ADDED: JAVA: t2mCfgCommand, command to configure eWON for Talk2M using Java. ADDED: Wizard block (basic WIZ, $dtWZ, web SSI WIZ) to read wizard progress data. ADDED: Talk2M Pro pr?liminary Support CHANGED: eWON Main page to avoid redirection (helps in case eWON web site is accessed through proxy) ADDED: a $flNOSSI option has been added to $dtUF to avoid SSI parsing if not wanted. ADDED: more monitoring of invalid authentication on web site. FIXED: When OpenVPN was configured for TCP connection and the server connection failed permanently, the watchdog was triggered. FIXED: Some special errors in OpenVPN lead to eWON reboot with critical error 20111. The OpenVPN process will now exit properly in case of error. FIXED: When WAN ethernet config is changed and the connection is established, it is now restarted to update the parameters. ADDED: JAVA:SysControl.saveBlockById: allows editing a User or Tag block with a given ID (not based on tag name or user login). ADDED: JAVA: NetManager.getVpnIp() which returns the current VPN IP address of 0.0.0.0 if VPN not connected. FIXED: MITSUFX IOserver: correct error message is now displayed in case of invalid address FIXED: IO server S7200: DataBits are now set on 8 by default ADDED: DNS_TTL config.txt parameterdefines in second the time to live of DNS entries. ADDED: Java monitoring functions in ModemManager: getDialoutCounter(), getGsmNetReg(), getGsmOpId(), getModemModemDetectionErr() ADDED: Java: ModemManager.updateClientInOut(void). Updates the amount of data exchanged during current dial out connection. ADDED: eVCOM software support: ablity to communicate with Siemens PLCs and HMIs on MPI remotely using eVCOM software version 5.5s1 ------------- FIXED: PROXY: eWON proxy feature Ext (WAN) to LAN was not working anymore since FW5.4s4 for outgoing PPP connections FIXED: S7200 Ioserver: PPI communication with eWON with MPI interface was not working. version 5.5s0 ------------- CHANGED: The Email configuration parameter length has been increased for 39 to 256 characters for publish by EMail. CHANGED: Empty username and password for ADSL config leads to ADSL not used and powered off. FIXED: MSN configuration parameter for ISDN modem was not working. CHANGED: When the WAN connection wizard is used for ADSL connection, the NAT is configured on the WAN interface. FIXED: when ADSL eWON was booting it could log up to 4 Open ADSL connection error because ADSL modem takes time to boot. The initial timeout has been increased to avoid this problem. FIXED: cosmetic error in internet connection wizard ADDED: OPEN UDP Basic function can force return TCP Port. FIXED: S73&400 ioserver: ISOTCPGW status counter cosmetic error fixed. Name of counter 2 in this section is now defined as "Number of ISOTCP S7 commands received". ADDED: MITSUBISHI IO server: a new IO server has been added to allow polling of FX PLC tags through the programming port. ADDED: S7200 IO server: PPI multimaster feature has been added to allow remote maintenance and polling of S7200 PLCs on a PPI multimaster network through the MPI port of eWONs equipped with a MPI port. ADDED: Endian firewall connection wizard added. FIXED: The ADSL connection time parameters was not used. A fixed value of 30 seconds was used instead. version 5.4s6 ------------- FIXED: a watchdog could occur on MPI eWON from CD familly when MPI was heavily communicating. FIXED: Java was not enabled on eWON 2101 MPI and eWON 4101 MPI version 5.4s5 ------------- ADDED: Support for S5-135 CPU928 PLC FIXED: When writing 'script' vars in viewON the console reported an 'invalid var name response' FIXED: MPI Chip was not detected on 'CD' family version 5.4s4 ------------- FIXED: Leased line modem was not working since 5.x FIXED: when a viewON script fails, the returned value was the result from a previous script. Now an invalid value is returned. FIXED: DHCP was not working with some DHCP servers. FIXED: When reading a binary /usr file with Basic command GET f,X, the output was the end of file at once, instead of X bytes. FIXED: Modbus RTU CRC problem since rev 5.3s7 for baudrates >2400 baud. ADDED: A web configuration page has been added to configure some debug features in eWON (in System/General config). ADDED: Support for ADSL eWONs (2104, 4104) ADDED: ((com.ewon.impng.io.j2me.comm.Protocol)(cc)).setBreak(boolean on) function for serial port access in Java FIXED: ADSL control port not be user accessible FIXED: S74 ioserver: following baudrates have been added when polling on the PROFIBUS bus: 9600, 45450, 93750, 500000 kbit/s. ADDED: Add DbgMode param can be added manually to AS511 driver to display PLC type in real time log and force 20 bit addressing. FIXED: Invalid IMEI is some devices updated FIXED: Debug configuration Web page was not working. Debug Flags were hard to enable/disable. FIXED: ADSL modem full reconfiguration failed. The problem occurred typically with new modem. FIXED: DHCP did not ask for IP address renewal. FIXED: ADSL Connection was not completely restarted when WAN connection timed out. FIXED: Proxy from EXT to LAN was not working on ADSL WAN interface. FIXED: ADSL When a lot of socket where NATed at the same time, some entries could be missed leading to retries. FIXED: Reset signal for ADSL was not working, reset was performed through power cycle. FIXED: Java function com.ewon.ewonitf.SysControlBlock(int BlockType, String RecordName) was not working and generated an illegal memory access. version 5.4s3 ------------- FIXED: Random crash at boot time due to hardware detection problem version 5.4s2 ------------- FIXED: DF1 IOserver: RsView gateway interoperabilty problem solved by adding bridge/no bridge EIP Connection configuration parameter. When bridging is configured EIP connections requests are forwarded to the PLC on the DF1 interface (Logix family case). This is the default configuration. When not configured, connection requests are cancelled by the eWON. FIXED: ABLOGIX ioserver: Tags are not updated anymore when an invalid tag type is received FIXED: GetFTP or GetHTTP may fail for unknown reason. This bug was introduced during fix of another bug related to cleanup of incomplete transfer of files by FTP. FIXED: When the VCOM was closed and it was not the default IO port, and error was reported. ADDED: Support for MPI/PROFIBUS up to 12MB on 2005CD and 4005CD version 5.4s1 ------------- FIXED: eWON WEB server rendered partial pages and images with some browser clients since revision 5.4s0. FIXED: eWON did not accept incomming call after boot until COM config was updated. eWON does check SMS or updated GSM level either. FIXED: DNS configuration was not applied at boot time. version 5.4s0 ------------- ADDED: S73&400 Ioserver: eWON allows multiple clients at the same time to access the same PLC through the ISOTCP-MPI gateway. ADDED: a new entry field called MSN can be used to enter a Multiple Subscriber Number for ISDN modems. If empty, all numbers are allowed. CHANGED: in the Web user interface 'Reset' term was used for 'Reboot' concerning an eWON restart or a modem restart. This has been changed. FIXED: Java com.ewon.ewonitf.ScheduledActionManager.SensSMSAction has been duplicated to SendSMSAction. FIXED: When the eWON had no modem or the modem was disabled (or not detected) and either an SMS was sent or the VCOM or Basic tried to access the port, an "Operation aborted, modem not available" message was issued. And port operation failed. FIXED: when a modbus error Acknowledge (code 5) or Busy (code 6) occurred, an error was reported in the events log and could not be filtered. The error is now reported as trace and can be filtered if required. CHANGED-ADDED: When the WAN interface is configured on the WAN Ethernet, the ethernet interface is really disabled and enabled when the WAN interface is disabled or enabled. Previousely, only the gateway was removed, but the interface remained active. REM: the link led goes off when disabled. FIXED: When there was a non ascii character in the eWON name, Talk2M user login or Talk2M user password, the Wizard did not work if these parameters were used. FIXED: in case the Eth1 or Eth2 IP address was invalid, the eWON COM config had to be reset to recover. Additional check have been added to track invalid IP address config. ADDED: The Modem led displays the connected or disconnected state. On a GSM modem, it now also shows the reception level. Please check the documentation for representation of the reception level. ADDED: ISDN specific parameter: MSN. GSM: operator selection. FIXED: when VPN is in "Listen for incoming VPN connection" mode, the "VPN Driver Mode" (ComCfg.VPNDrvMode) is now forced to TUN to re-enable eCatcher or eWON PTP access. A reboot is required. FIXED: when an FTP transfer to the eWON failed because the /usr file system was full, the file was closed with an incomplete content. In that case, the partial file is now deleted. FIXED: when DHCP failed WAN connection did not fail, but no there was no connectivity. FIXED: After a full reset, the WAN connection type was not set correctly. User had to use the "default config" button to have the 'real' default config. ADDED: New global TCP timeout parameter for all IO servers. This parameters can be used on slow TCP/IP networks where the old default 1000 MSec timeout was too short. ADDED: S73/400 ioserver: PROFIBUS integration: eWON is now able to allow remote programation and monitoring, as well as polling of S7 PLCs located on a PROFIBUS bus whithout disturbing the traffic. ADDED: if PIN code is empty, the eWON will still check if the modem is not already READY (the SIM does not require a PIN code) FIXED: ABLOGIX ioserver: Device Address specified at tag level is now correctly supported. FIXED: When OpenVPN was configured to work through proxy, and the proxy was not responding, the eWON rebooted with a watchdog in OpenVPN process. The VPN process will now retry Proxy connection correctly. FIXED: "Operation aborted, modem not available" was reported during configuration although modem usage was not requested. ADDED: Basic function: WAIT, added to monitor reception of data on TCP/UDP files. FIXED: in case the "route all traffic through VPN" is selected and there is no gateway defined in the eWON and the HTTP proxy was used, there was an error message generated. FIXED: the PT100 analog is now filtered by a sliding average on 8 values for noise filtering. CHANGED: the println command in JAVA has been optimized for buffered write access to files. Writing byte per byte was quite slow on /usr files. FIXED: When OpenVPN tries to resolve the VPN server but DNS request fails continuously, and the VPN is being closed, the the system is blocked and a watchdog occurs in the OpenVPN thread. ADDED: Support for Endian VPN/Firewall server. See http://www.endian.com. ADDED: a trace is added in the event file when the callback is programmed. FIXED: Socket number could leak if a TCP connection that was opened on a WAN server is closed after the WAN (PPP or Ethernet) interface has been closed (in other words: if the route to the server does not exists any more). version 5.3s8 ------------- FIXED: DF1 IOServer: eWON was displaying wrong values when serial bus desynchranisation occured FIXED: parsing problem for server name (in user:pass@server.com:port,xx syntax) prevented FTP transfer when a global server was specified. Problem could also affect HTTP, SMTP and NTP). FIXED/CHANGED: The GET x,y function applied to /usr files will return between 1 and y bytes when end of file is reached. Previously the function could only return y bytes and the user had to compute the number of bytes left in the file for the last read. FIXED: S73&400 io server: eWON MPI communication with PLCs is not anymore disturbed when broadcast messages are exchanged between PLCS FIXED: In some case, when a client FTP operation failed (PUTFTP or GETFTP), the following operations executed on the same FTP server could also fail (the eWON reported a "Server response timeout" error forever for example). FIXED: When operator selection was set to automatic, the eWON sometime reported an incorrect "operation selection failed" message. version 5.3s7 ------------- FIXED: the bootloader upgrade upgrade could fail and the eWON needed to be sent to factory for repair. FIXED: Modbus did not work correctly for baud rates smaller than 2400 baud but only in RS232/RS422 mode (not RS485). FIXED: There was a cosmetic problem with the display of the Proxy external interface in Internet Explorer when the proxy was disabled. version 5.3s6 ------------- FIXED: DF1 IOSERVER: eWON is now able to act as gateway between a CompactLogix and a MicroLogix. version 5.3s5 ------------- FIXED: S7&400 ioserver: global device address specification is now correctly solved. FIXED: When sensitive security mode is enabled, the existing user's password were not encrypted. Now they are and the config changes are saved. FIXED: a regression in firmware 5.3S4 prevented the $ctG (compression in export bloc descriptor) from working. ADDED: eproxy: proxy allow now to apply to WAN, PPP incoming and VPN external interfaces FIXED: Added and validated support for Siemens S5 115U CPU 945 PLC. ADDED: eproxy: Port and IP address information has been added to the "UDP destination address conflict" error message version 5.3s4 ------------- FIXED: STATIC ROUTES: event log message Add Static Route displays now correctly the ip address and mask address FIXED: S73&400 ioservers: global device address specification at tag level for an ISOTCP connnection is now supported FIXED: getftp of ewonfwr.edf over PPP connection failed with a n OUT OF MEMORY error and the eWON rebooted. FIXED: When the ewonfwr.edf file is transfered using the HTTPGet, FTPGET or JAVA Loader, the eWON did not start the upgrade process. The eWON will now start the upgrade process for these transfer as soon as they have successfully finished. CHANGE: Proxy sever label in Talk2M wizard signals that server NAME is not accepted (only IP address). FIXED: $dtTR (TAR export) did not support compression, except if $td argument was using {} to enclose parameters AND if $td was the first tag after $dt. ADDED: The tag definition content obtained through GetSys tag or any other config export has an additional item called ALTYPE that can take the following values (see General User Guide: 8.3.10.3 'Alarm type values) FIXED: ISDN protocol used for sending SMS (TAP/UCP) has been changed from V120 to X.75 for operator compliance. CHANGED: All VPN eWONs default to Talk2m wizard and feature enabled (no need to use BootOp parameter). version 5.3s3 ------------- FIXED: In Talk2M (actually when using a TAP driver for VPN), the TPC memory leaked until the VPN connection was closed. When the TCP memory reached 1MB, the eWON reboot (check done every 10 minutes). FIXED: When there was a space character in the eWON name, Talk2M user login or Talk2M user password, the Wizard did not work if these parameters were used. FIXED: T2M: If the WAN connection was active when the Wizard was started, the eWON tried to start the WAN anyway, leading to incorrect behavior. version 5.3s2 ------------- FIXED - CRITICAL: The watchdog mechanism was not working any more and the memory overrun test was executed too often resulting in a firmware performance and stability issue. ADDED: the TEC (SMS) alarm protcol has been added. FIXED: a bug in the ISDN modem could lead to occasional or frequent (depending on modem) connection establishment failure and occasional PPP disconnections. A workaround has been implemented to avoid these problems. FIXED: incorrectly reported error ("Operator selection failed") during modem detection. version 5.3s1 ------------- FIXED CRITICAL: This error introduced in version 5.3s0 happened at least 30 minutes after eWON has booted. When an SMS is sent, the eWON reports an error: "eppp-Modem inaccessible to PPP for a very long time" This message was displayed after every SMS sent. 12 hours after the eWON had been started, immediately after an SMS was sent, the eWON rebooted with a critical error: "Modem inaccessible to PPP for a very long time". REM the same error could occur if VCOM was configured and used on the modem port. FIXED: Problems with Talk2M wizard in French. Accented characters were not displayed correctly in test results and "Termin?" button was not displayed. FIXED: MODBUS IOserver: status flag indicates the correct value now even when the cable is disconnected FIXED: DF1 IOserver: polling using direct ethernet connection works again. version 5.3s0 ------------- ADDED: ABLOGIX IO server: Support of DF1 protocol to access directly connected ABLOGIX PLCs has been added. This allows as well polling of tags than remote maintenance. FIXED: When "Ethernet WAN connection" is selected for "Internet access" the "Maintain connection" checkbox is checked (and saved) in the Web GUI. FIXED: IO server: A global configuration parameter TagPollMode has been defined. When set to 1, tag polling is disabled for a given tag when a protocol error occurs when reading this tag. When set to 0 (default case), tag is not disabled when a protocol error occurs for this tag. The value of the TagPollMode parameter is defined in the system section of the config.txt file FIXED: when the real time graph min and max are equal a minimum scale of 2 units is set to enhance readability. FIXED: In Internet explorer (6 or 7), a large gap could appear between menu and column header of viewIO or RT Alarm table due to the HTML generated (more visible with large number of tags). FIXED: A race condition in JVM shutdown when reading an event at the same time could cause an illegal memory access reboot. ADDED: Talk2M: The Wizard now includes a warning saying that "Internet connection must be configured" In case the internet connection is configured to "None", an explicit error message is produced. ADDED: Talk2M: A trace is now logged when the user request WAN disconnection from eCatcher. ADDED: Talk2M: if maintain connection is enabled on a modem internet connection, then a warning is added during wizard operation. FIXED: ABLOGIX ioserver: iosend command is now handled correctly when used with the ABLOGIX ioserver. FIXED: Talk2M: When clicking wizard "done" button an error page was displayed. FIXED: encoding of date and time was not possible for dates in 1970. FCNV for example did not work for year 1970. FIXED: TAR EXPORT BLOCK DESCRIPTOR: Files belonging to a TAR EBD do not stay anymore locked when a PUTFTP/PUTHTTP operation holding this EBD fails. It is now possible to delete this files even if the PUTFTP/PUTHTTP fails without rebooting. FIXED: There could be a conflict between the scheduled action manager and the PPP modem manager when both tried to access the modem. This could result in longer modem detection and modem reset operations. Sometimes the SMS operation could fail. ADDED: DF1, ABLOGIX IO server: it is now possible using EIP to poll PLC tags located on a DH+ network, behind a controllogix (equipped with an EIP card and one or more DHRIO cards). FIXED: using ISDN, SMS transmission failed in the TAP and UCP protocol failed on most provider that required V.120 protocol. The eWON now uses the V.120 protocol for UCP and TAP. FIXED: ABLOGIX, DF1 IOserver: eWON reads now the integer typed tags as signed integers. ADDED: Feature EF0006 disable viewON from the eWON FIXED: ISDN eWON with faulty DTR signal will now work because modem is configured to ignore the DTR signal. version 5.2s1 ------------- FIXED: when WAN and VPN were established and Talk2M wizard was started, the wizard failed in the UDP connectivity test and the HTTP mode was used. FIXED: PROXY: UDP proxy ports are now still working even when a communication error occurs on the sockets implementing the proxy service on this port. FIXED: IOSERVER S7200: downloading of programs with MICRO/WIN is working now. CHANGED: GET on a TCP file returned an empty string when the socket had been closed by the other side. Now GET returns an error when the socket has been closed. FIXED: IOSERVERS: all IO servers support now lower and uppercase for tag addressing (including status tag) FIXED: Error texts where missing for AS511 error codes 30130 and 30131. FIXED: When the firmware was transfered and during the transfer the eWON status where read (INF block), the transfer failed with an incorrect checksum error. The error was reported during long transfers through GPRS. ADDED: FCNV and SFMT basic commands have an additional conversion type to convert time from string to integer (number of seconds since 1/1/1970) and the opposite. ADDED: Alarm hint has been added to the rt_alm.txt file. CHANGED: ping.talk2m.com IP address is now hard coded to avoid DNS error during talk2m wizard. Talk2M VPN server uses now hard ip address as first server and ewon.talk2m.com in second position ADDED: When the "Ethernet WAN connection" is selected in the "Internet access" configuration, the "Maintain connection" checkbox is now automatically checked. CHANGED: The alarm "activation delay" is now also applicable after the alarm return to normal state. Previously the alarm was triggered immediately when in RTN mode. FIXED: the VCOM Inactivity Timeout parameter did not work, even if its value was different from 0 it worked as if it was 0 (disabled) CHANGED: NFR (Demo units) eWON will not be blocked any more after 12 hours. A "Demo Unit" message is displayed on the eWON welcome page. version 5.2s0 ------------- FIXED: S73&400 ioserver: eWON recovers now automatically from "Offline State" ADDED: configurable unconnected action timeout. Normal watchdog mechanism will start at expiration of this timer. ADDED: Reporting of tag errors has been improved: Tags in error are reported and are not polled anymore unless explicit polling reinitialisation of the IO server by the Operator using web interface ADDED: Getsys PRG,"VPNIP" returns 0.0.0.0 if VPN not connected or the VPN IP address if VPN is connected. ADDED: VPNIP value is added to the estat.htm or $dtES info bloc. FIXED: the Modbus advanced "TcpPort" parameter was only applied when the serial port was opened. FIXED: When an empty passphrase for VPN was entered, and the eWON tried to use it it caused an eWON reboot on watchdog. FIXED: When the eWON called back a user and the user connected to the eWON through VPN, the eWON hung up after the "Wait for user login for" time, even if the user had connected to the web site. FIXED: The "IP services configuration" page was not accessible on eWON 500 FIXED: "INF" bloc was not working in Getsys, Setsys operations. FIXED: In UNITE IO server, it was impossible to disable "Force Unitelway V2" from the config web page. FIXED: the SNMP Host 1 entry was displayed rwice. ADDED: 2 additional fields added to the estat - INF bloc: DskUsrFree, DskUsrTotal for flash partition monitoring. CHANGED: IOServers: The error message "Protocol Error while reading Tag (Tag Name)" has been changed to: "Protocol Error while reading Tag (Tag Name - Polling disabled for this tag)". This change apply for all IOservers. CHANGED: S7200, S73&400 IOServers: the Tag Error messages "Error in read subrequest response" and "Class error in read response" are now reported as warnings. FIXED: S73&400 server: Invalid Diagnostic error message (S74srv-Error in read subrequest response) is not displayed anymore at startup when a status tag is defined together with other tags. FIXED: Proxy: Watchdog does not occur anymore at eWON startup when early update of configuration has to be done. ADDED: LayDir parameter ADDED: 2 additional fields added to the estat - INF bloc: CfgFreeMem, PrgFreeMem for config memory monitoring. version 5.1 S2 -------------- FIXED: When serial debug was enabled on VCOM ports, the eWON could crash because of illegal memory access. FIXED: S73&400 ioserver: Boolean Tag polling problem solved FIXED: When 'maintain connection' was enabled, AND it was not posssible to establish the WAN connection. The unconnected actions (PUTFTP, GETFTP ...)were pending for ever (In Progress) FIXED: MaxDeltaReg could not be bigger than 10, MaxDeltaCoil could not be bigger than 100. If bigger values where entered the eWON crashed with illegal memory access. New values are MaxDeltaReg <=124 and MaxDeltaCoil <= 256 (limits are checked) FIXED: when restoring a config with modbus IOServer used, the eWON generated an error and modbus was not configured ADDED: If an integer is passed to the Basic SetTime function, the function take the paramter as seconds since 1/1/1970 FIXED: When using PutFTP with an inexistant FTP server address, then eWON did not free the socket resulting in an eWON reboot when too many socket were opened. FIXED: After a full reset the Modem Init String was empty, now it takes the default value according to the installed modem. CHANGED: added +CSNS=4 to gsm default init string to force data call when not specified by operator. FIXED: The reset timeout was too short for some older GSM modem (Type 1) that could lead to multiple reset sequence and slow (to no) detection version 5.1 S1 -------------- CHANGED: Default value for "Force Unitelway V2" in UNITE IO Server is now TRUE. FIXED: an invalid error message was issued in the events file at every reconfiguration of the modbus IO server (error code: 22509). FIXED: Modbus at 600 baud was not working because of the inter char delay value used. FIXED: routes are added even if a gateway does not respond to ARP request. There could be a problem when route were added while the gateway was unavailable. In that case, the gateway could be omited. FIXED: When: - The eWON could accept incoming PPP calls - The 'Use incoming for outgoing' option is selected (meaning the PPP connection must be configured as a default gateway) - An Ethernet gateway was configured - The eWON had only one ethernet interface - Internet connection was set to 'None' Then, when the incoming PPP communication was closed, the ethernet gateway was not reconfigured. FIXED: Incorrect behaviour for eWON with an ethernet WAN interface, when 'Use incoming for outgoing' is enabled on PPP and a call is received, the WAN gateway is lost and WAN com is disrupted. Now WAN gateway is not modified any more. FIXED: It was not possible to display the MPI station popup on WebPort FIXED: When the basic was started with a cyclic section. If at the same time the user tries to browse the eWON web site he may trigger an HTTP watchdog. This only happened if the user browse the web site during the first 3 minutes after eWON boot and when a cyclic section is actively running. version 5.1 S0 -------------- CHANGED: Unitelway IO server default value for "Force unitelway V2" has been changed to TRUE, as this improves communication quality. This is the default value when a new config is created for the IO server. FIXED: S73/400 IO Server: List of active stations is now updated when the MPI address of the eWON is reconfigured. FIXED: S73/400 IO Server: implicit routing feature is now working with S7400s even if the CPU is not located in the slot 2 of the rack. FIXED: in some rare case, the eWON web server could enter a state where it did not respond to any new request. FTP, and all other services were still working but Web server seemed dead. ADDED: it is now possible to upgrade the boot loader (bootldr.bin). This is required for supporting futur 5.2 firwmare. FIXED: S73/400 IO Server: MPI sesssion establishment does now succeed with 315-2DP PLC models. ADDED: DF1 IO Server: Add support for PLC5 PLCs FIXED: The Enable IP Forwarding check box was not displayed any more in the user interface (Update was still possible using the comcfg.txt RTEnIpFwrd field). FIXED: restore of backup.tar files in the eWON using eBuddy or directly by droping the files in the eWON by FTP had a random behaviour. Sometimes, some files were not restored. version 5.0 S7 -------------- ADDED: S73/400 IO Server: MPI implicit routing feature. When the S73/400 IOserver receives ISOTCP requests containing only a local TSAP, it will forward the requests to the Destination MPI node configured in the gateway configuration section. FIXED: When the "Internet Access", "Network Connection" is set to "No Internet Access", and an outgoing connection (like SENDMAIL or PUTFTP) must occur, but the eWON has no gateway defined, then eWON can enter an infinite loop that ends with a watchdog in process "unact" FIXED: S73/400 IO server: eWON now leaves slow poll mode when Status tag is polled ADDED: S73/400 IO Server: display of MPI neighbours 'inring' station status to make MPI configuration more user friendly FIXED: All IO servers now actually enter in slow poll mode even if the status tag is not defined. Polling rate is now adapted. ADDED: S73/400 IO Server: MPI communication efficiency improved using the MPI bus access control information. When a destination MPI station is not detected as 'inring' the application commands are not sent anymore to the bus, and a non protocol error is immediately returned to the application. In the case of tag polling the ioserver enters in slow poll mode when the number of retries is exceeded. FIXED: S73&400 IO server: MPI sessions are now closed correctly for all S7300 PLC models. FIXED: FINS gateway was not listening on port 9600 in release 5.0 FIXED: FINS: FINS gateway was not working in UDP mode FIXED: GMT Offset edition now allows fractional GMT offset (in the config.txt the offset is anyway stored in seconds) FIXED: Critical issue: when the file system (/usr) was corrupted it could be impossible to perform a "button full reset", only the Power and DO led were on after boot and eWON had to be sent for repair. ADDED: There is a new "advanced" TCP parameter in ModbusIO server configuration called 'TcpPort' that can be used to change the default 502 port used when eWON connects to a ModbusTCP server. If not specified the 502 default value is used. This Port value is used for all ModbusTCP client connections. ADDED: S5 AS511 IO server now supports additional format modifier. The following where existing: B (byte), W (word), D (signed DWord), the following has been added C (char -128 -> +127), S (short: -32768 -> +32767). The DWORD itement cannot be accessed as unsigned elements. version 5.0 S6 -------------- FIXED: When the 'Storage' configuration was configured with a /sys size of 0 MB, it was not possible to perform a backup/restore of eWON. FIXED: the Basic additional timeout paramter for OPEN "tpc:..." was not used and internal default 75 seconds was used instead. FIXED: DF1 IO server: S tags are now writable ADDED: FINS IO server: new data types added FIXED: S73/400 IO server: MPI Response Timeout is now configurable FIXED: S7200 IO server: PPI reply timeout is now configurable FIXED: S73/400 IO server: MPI is now compatible with CPU416-2 K04 model ADDED: QWAVE IO server trace facilities FIXED: QWAVE IO server: events retrieval algorithm improved by changing the start time of retrieval FIXED: S73/400 IO server: polling of the correct DBs is now done when multiple DBs are polled simultaneously. ADDED: QWAVE IO server: optional QWAVE login procedure FIXED: S73/400 IO Server: CPU416-2 DP (S7400) is now supported by eWON. version 5.0 S5 -------------- IMPORTANT: since this revision, when the eWON has an out of memory condition, it will reboot with a critical error. The previous behaviour was to try and recover from the situation but usualy resulted in unstability. Some eWON that seemed to work with stressed memory condition could now reboot with this error message in the event log. FIXED: When a huge and fake HTTP request (URL 1>MB) was sent to the eWON a memory corruption could occur causing the system to lockup until power is cycled. FIXED: DF1 ioserver was not able to poll MicroLogix 1100 using ethernet port. FIXED: DF1 ioserver was not able to read or update tags defined with an element number (address inside the file item) equal to 255 FIXED: The advanced USecDelay for MODBUS IO server was not applied at boot time, but only when config was changed. FIXED: eWON "version codename" did not contain the language preventing eBuddy from displaying the eWON's language FIXED: D01 was not working on all eWON except 1002/4102/4002 version 5.0 S4 -------------- FIXED: FINS ioserver: Handling of device addresses defined at tag level was not done correctly CHANGED: Better NTP protocol implementation. The message round trip time between eWON and the NTP server is now compensated. FIXED: When the s73&400 ioserver of the eWON was busy polling a given PLC and this one was rebooted it resulted in the reboot of the eWON as well by watchdog. FIXED: DF1 ioserver didn't read/write correctly Input/Outputs of the MicroLogix PLCs FIXED: When default MPI address was left empty in the configuration, address 1 was used instead of 0. The default value is now correctly set to 0. FIXED: Memory config other than default could lead to incorrect behaviour and reboot loop until full reset. On eWON with 8MB Flash (all non VPN eWON), then following problem occures: If a memory config with a /sys parition size of 0 (3 last options in the menu) is selected, the eWON will reboot continuousely until a full reset is perfomed. On VPN eWON (with 16MB flash): If a memory config with a /usr partition size of 4 MB (last option of the menu) is selected, the config will be stored in the /usr partition instead of the hidden /sys partition, this may cause trouble if the user formats the /usr partition. FIXED: DF1 and ABLOGIX ioservers were using value 0 as Ethernet/IP port to establish connections to AB PLCs FIXED: Edition if EWON or QWAVE IO server config through web access returned an error. version 5.0 S3 -------------- FIXED: ewon.cgi shortcut was not protected. It is now protected by Web authentication. FIXED: On eWON with only 1 ethernet interface, when a gateway was defined, it was never used. Now the Gateway is configured as a default gateway all the time IF the "Internet connection" is configured to "No Internet access" (Otherwise, the PPP connection is the gateway) FIXED: When a WAN connection failed (PPP dialout failure for example) during a Sendmail, PutFtp, NtpSync, etc. A watchdog could occure in the scheduled action process (unact). FIXED: MPI upload/download of PLC failed when CPU was not in Rack 0 Slot 2 FIXED: S73/400 ioserver last variable of a DB block could not be read FIXED: During harwdare reset and reconfiguration of MPI bus parameters, the eWON disrupted the MPI bus and other devices went temporarily offline FIXED: When dialing in an eWON with PPP, the reported IP address was 0.0.0.0 for the PPP interface (reported address was invalid but connection was working). ADDED: FCNV Basic function was extended and SFMT function was added to make it easier to write custom protocol (easier frame decoding and coding). CHANGED: User's password are now encrypted in the configuration (config.txt) if the "encrypt sensitive data" flag of the COM Cfg is set. version 5.0 S2 -------------- FIXED: the default value for "Number of rings before modem answers" in configuration web page was invalid (was 0), it has been changed to 1. FIXED: PUTFTP and GETFTP code was broken in version 5. The eWON crashed with an "illegal memory access" error for some specific PUTFTP, GETFTP parameters length. FIXED: the default value displayed (was 0) for "Reset budget period" in the configuration web page was invalid. FIXED: the web server connect window now displays the eWON's identification in the "realm" field. FIXED: source name reported in event log was incorrect for elog, unact and alarm. ADDED: The OPEN "tcp:..." basic command has been extended to support an OPTIONAL additional "connection timeout" parameter. If present the timeout is separated from the port number by a ',' and specified in seconds (ex: "tcp:10.0.0.1:80,10") ADDED: BREAK support added to VCOM in RFC2217. The Break status from the client side in now applied to the eWON port (REM: a break on the eWON port is not reported on the client port) version 5.0 S1 -------------- FIXED: Wrong values read when group of tags of same memory type are defined in S7200 and S7300/400 IO Server FIXED: Update of Counter memory type tags impossible with S7200 IO Server version 5.0 S0 -------------- - New GUI - MPI Support - VPN Support